Search found 49 matches
- Fri Jul 31, 2020 2:02 pm
- Forum: s300 / SManager
- Topic: Code 41: Oxygen Sensor Heater
- Replies: 10
- Views: 4898
Re: Code 41: Oxygen Sensor Heater
Please try this. There is no way it can take some changes and not others. Hi, got a radiator pipe busted because of which the car is in the garage. I wanted to check with you, I use the x64 version for the sManager whenever I upload the map. Do you think that could be the reason for the s300 to not...
- Mon Jul 27, 2020 6:58 pm
- Forum: s300 / SManager
- Topic: Code 41: Oxygen Sensor Heater
- Replies: 10
- Views: 4898
Re: Code 41: Oxygen Sensor Heater
Okay, will do so and revert back.
- Mon Jul 27, 2020 3:48 pm
- Forum: s300 / SManager
- Topic: Code 41: Oxygen Sensor Heater
- Replies: 10
- Views: 4898
Re: Code 41: Oxygen Sensor Heater
I haven't done such a test. But you think the s300 is accepting only some changes and not all?
- Mon Jul 27, 2020 3:13 pm
- Forum: s300 / SManager
- Topic: Code 41: Oxygen Sensor Heater
- Replies: 10
- Views: 4898
Re: Code 41: Oxygen Sensor Heater
I do the changes, save the map and keep the key in the ignition position and click on the upload arrow.
- Sun Jul 26, 2020 6:06 pm
- Forum: s300 / SManager
- Topic: Code 41: Oxygen Sensor Heater
- Replies: 10
- Views: 4898
- Sat May 30, 2020 7:51 am
- Forum: s300 / SManager
- Topic: Code 41: Oxygen Sensor Heater
- Replies: 10
- Views: 4898
Code 41: Oxygen Sensor Heater
S300 Serial Number: 42771 SManager Version Number: 2.7.5.0 Calibration: Attached Datalog: Unavailable Vehicle: 1996 Honda Civic Del Sol VTEC, B16A6 ECU: P28 Modifications: Top Fuel Air Intake, Skunk2 Gen1 Intake, 4-2-1 PLM Headers, Tanabe Medallion exhaust. Problem: My calibration has the O2 heater ...
- Thu May 14, 2020 11:26 am
- Forum: Civic Type R 2007-2011 European FN2
- Topic: K20Z4 Swap FD - P0135 O2 heater circuit
- Replies: 2
- Views: 6248
Re: K20Z4 Swap FD - P0135 O2 heater circuit
Thanks Spunkster. Some other folks here said the same. Will add the OEM sensor as well.
- Tue May 12, 2020 11:44 am
- Forum: Civic Type R 2007-2011 European FN2
- Topic: K20Z4 Swap FD - P0135 O2 heater circuit
- Replies: 2
- Views: 6248
K20Z4 Swap FD - P0135 O2 heater circuit
Hi all As the subject states this question is for my friend's K-Swap FD. Recently we I stalled AEM UEGO 30-4110 kit on his car. The ground is given to the same point as the ECU on the intake manifold. The white cable for datalog is connected to the ELD pin on the ECU and in the flashpro manager I ha...
- Tue May 12, 2020 11:29 am
- Forum: S300 Calibrations
- Topic: Check Engine light no error code!
- Replies: 4
- Views: 4363
Re: Check Engine light no error code!
Everything is working as it should. There seems to be a grounding problem with my car as I shifted my ground wire for the wideband from ECU pin to the thermostat body and I still need to set a -0.25 voltage offset. I have coolant leak and minor oil leak as well so will be fixing that too. Thanks for...
- Thu May 07, 2020 5:13 pm
- Forum: S300 Calibrations
- Topic: Check Engine light no error code!
- Replies: 4
- Views: 4363
Re: Check Engine light no error code!
What is the serial number that is on the s300 board inside the ECU? From Help, About, what I the version of software you are using? I would recommend that you fix any leaks and check to make sure that the head gasket is not damaged. Will check these and reply back. The tuner sent me a new map. He's...
- Thu May 07, 2020 10:17 am
- Forum: S300 Calibrations
- Topic: Check Engine light no error code!
- Replies: 4
- Views: 4363
Check Engine light no error code!
Hi All, So I've been e-tuning my B16A Delsol with a friend in Germany. Very basic he send me the calibration I datalog and send him back. Up until yesterday everything was running fine. The calibration he sent me today showed me a check engine light right from key in the accessories position, rpm wa...
- Thu Feb 06, 2020 11:38 am
- Forum: s300 / SManager
- Topic: AEM UEGO 30-4110 Install
- Replies: 33
- Views: 8868
- Thu Feb 06, 2020 11:36 am
- Forum: s300 / SManager
- Topic: AEM UEGO 30-4110 Install
- Replies: 33
- Views: 8868
Re: AEM UEGO 30-4110 Install
Dear All, thank you for your support. I figured what the problem was. In the Parameters-closedloop advanced tab there's a setting for input voltage source. Those settings were wrong. I changed them to setup as per AEM and the I had to adjust the voltage offset to -0.30(autocorrected by s300 to -0.29...
- Wed Feb 05, 2020 4:14 pm
- Forum: s300 / SManager
- Topic: AEM UEGO 30-4110 Install
- Replies: 33
- Views: 8868
Re: AEM UEGO 30-4110 Install
A few shots of showing the AFR differences...
- Wed Feb 05, 2020 3:59 pm
- Forum: s300 / SManager
- Topic: AEM UEGO 30-4110 Install
- Replies: 33
- Views: 8868
Re: AEM UEGO 30-4110 Install
I was just telling you what I use and what results I typically get. In the closed loop advanced tab you have the wideband input set to D10 ELD. But you also have a screenshot of the analog input set for a wide band. Where is the analog out going from the wideband, the Analog plug on the S300 board ...