Search found 30 matches

by Diogo Oliveira
Fri Apr 05, 2019 9:31 am
Forum: K-Pro Calibrations
Topic: Tuning advice needed on BC Stage 2 K20a for circuit car
Replies: 4
Views: 3578

Re: Tuning advice needed on BC Stage 2 K20a for circuit car

Sorry for no replying earlier, sometimes I forgot to check here. You can reach me at me email - wakko.tm@gmail.com - since I check it more often. You want the car to run in Open Loop all the time unless you are going for an endurance race and fuel economy is a key to finish the race in a good positi...
by Diogo Oliveira
Thu Mar 28, 2019 8:47 pm
Forum: K-Pro Calibrations
Topic: Tuning advice needed on BC Stage 2 K20a for circuit car
Replies: 4
Views: 3578

Re: Tuning advice needed on BC Stage 2 K20a for circuit car

The flatness mentioned is because T.Pedal goes to zero, meaning you are lifting your foot from throttle. The spykes are occuring when the ECU goes from closed loop to open loop. A/F is everywhere and closed loop parameters must be better dialed. Since this car is for circuit racing, there are some t...
by Diogo Oliveira
Thu Mar 28, 2019 8:08 pm
Forum: FlashPro Calibrations
Topic: Tuning Air/Fuel Help 2009 Civic Si
Replies: 8
Views: 3762

Re: Tuning Air/Fuel Help 2009 Civic Si

You are using a hybrid calibration with AFM enabled, you need to tune the AFM sensor and not the WOT tables. Its a little bit more complicated to tune and takes more time, but it works just fine. You could just mark the 'Use speed / density tables" under Calibration - Fuel and tune your engine ...
by Diogo Oliveira
Wed Dec 12, 2018 3:45 pm
Forum: Civic Si 2006-2011 Americas
Topic: Knocks only in cylinder #3. Attached fpcal and data logs
Replies: 3
Views: 2779

Re: Knocks only in cylinder #3. Attached fpcal and data logs

Try adjusting spark plugs gap. NGK comes with 1.1 gap from factory, but 0.8 works better (Denso spark plugs have 0.8 from factory if Im not wrong).
by Diogo Oliveira
Wed Apr 11, 2018 10:52 am
Forum: Civic Si 2006-2011 Americas
Topic: Could someone take a look at this datalog?
Replies: 3
Views: 1921

Re: Could someone take a look at this datalog?

A/F is ok, a bit rich at that 2nd gear pull, and S.TRIM is pulling out lots of fuel while in closed loop....I would say there should be some fuel coming out from the exhaust.

Your engine wont get damaged and you can run the basemap forever. But you will see a big difference if you get a custom tune.
by Diogo Oliveira
Fri Oct 02, 2015 7:12 am
Forum: K-Pro Calibrations
Topic: Projeto para Brasil
Replies: 2
Views: 2439

Re: Projeto para Brasil

Check your pm's
by Diogo Oliveira
Thu Dec 18, 2014 6:45 am
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74289

Re: FlashProManager v2.0.0

Have you checked how the WOT lambda tables are set?
by Diogo Oliveira
Wed Sep 03, 2014 11:34 am
Forum: FlashPro Manager
Topic: VERSION 1.8.3
Replies: 3
Views: 2871

Re: VERSION 1.8.3

You cant downgrade the software just because you cant downgrade the firmware. Have you saved your calibration with version 1.9.3 and upload it again? I don't have this issue with any of the cars I had updated the calibration.

Can you post a datalog and the calibration you are using?
by Diogo Oliveira
Fri Jun 06, 2014 10:28 am
Forum: s300 / SManager
Topic: NEED HELP TO INSTALL ON WINDOWS 8
Replies: 15
Views: 6677

Re: NEED HELP TO INSTALL ON WINDOWS 8

I do....SManager, K-Manager and FlashPro Manager, all working as it should. Check if you have admin permissions and also re-check if you dont have any AV or firewall enabled (even windows 8 firewall or any ther built in Windows security system). I did not had to use compatibility mode to install. Al...
by Diogo Oliveira
Tue May 06, 2014 3:17 pm
Forum: Traction Control with FlashPro
Topic: Traction Control stopped working
Replies: 8
Views: 16448

Re: Traction Control stopped working

I used SManager to try to setup Traction Control. This suggestion I took from this topic: http://www.hondata.com/forum/viewtopic.php?f=43&t=17114&start=15#p74638 - I only used SManager to try to setup TC parameters and see if something different would happen. The datalog I have posted was ma...
by Diogo Oliveira
Mon May 05, 2014 5:05 pm
Forum: Traction Control with FlashPro
Topic: Traction Control stopped working
Replies: 8
Views: 16448

Re: Traction Control stopped working

Ok.... After testing it with almost all the cars that are having this issue, I got nothing. Downloaded TC Manager 1.0.7, got everything setup, saved the calibration, uploaded to TC unit and closed TC Manager window. Unplugged the USB cable for TC and started FP Manager.....and nothing changed. The i...
by Diogo Oliveira
Sun Apr 27, 2014 10:04 am
Forum: Traction Control with FlashPro
Topic: Traction Control stopped working
Replies: 8
Views: 16448

Re: Traction Control stopped working

Traction Control
V1.0.7
Firmware 10

FlashPro Manager
V1.8.2
Firmware 64
by Diogo Oliveira
Sat Apr 26, 2014 12:51 pm
Forum: Traction Control with FlashPro
Topic: Traction Control stopped working
Replies: 8
Views: 16448

Re: Traction Control stopped working

Forgot to mention:

Flash Pro Manager version 1.8.2

SManager version 2.2.7

I can try something using KManager if that helps you to replicate the problem.
by Diogo Oliveira
Sat Apr 26, 2014 12:44 pm
Forum: Traction Control with FlashPro
Topic: Traction Control stopped working
Replies: 8
Views: 16448

Traction Control stopped working

This is happening for a while now.... After updating FlashPro Manager to version 1.8.x, Traction Control stopped working. It simple stopped working as it should and I don´t know what happened.....none of the units are "new installation", it was installed for some time and it was working pr...
by Diogo Oliveira
Tue Apr 15, 2014 11:31 am
Forum: FlashPro Manager
Topic: no power on flashpro module
Replies: 28
Views: 10642

Re: no power on flashpro module

Just checked my customers non BT FlashPro, its working as it should.