Search found 18 matches

by akep
Wed Nov 22, 2023 9:11 pm
Forum: K-Pro / KManager
Topic: Can't upload tune - registration required
Replies: 3
Views: 1286

Can't upload tune - registration required

tried to use this ecu and it said needed to update drivers and kpro software (from current to beta) then it said i needed to register before uploading. same as the earlier posts but all green in info panel and otherwise everything in the software looks ok (on line, drivers installed, no locks) i eve...
by akep
Fri Oct 22, 2021 3:04 pm
Forum: K-Pro / KManager
Topic: CAMCMD reads 0 but map says otherwise
Replies: 2
Views: 840

Re: CAMCMD reads 0 but map says otherwise

yep we found a part of the harness was not secured and it rubbed through a wire on the water neck and it was shorting, causing the ecu to reset. When moving the throttle body we found it would hiccup and as we tugged on the harness it was priming the fuel pump over and over again. wrapped it and sec...
by akep
Mon Oct 18, 2021 7:35 pm
Forum: K-Pro / KManager
Topic: CAMCMD reads 0 but map says otherwise
Replies: 2
Views: 840

CAMCMD reads 0 but map says otherwise

In the attached datalog you can see the first 2.5 minutes the cam angles are doing as intended, then in 2:50.5 the VSS and CAM blip and go to 0, then immediately after the same thing happens (we are troubleshooting, the car has suddenly started falling on its face like lean/boost cut, also artifacts...
by akep
Wed Apr 22, 2020 5:07 pm
Forum: K-Pro / KManager
Topic: Launch Control Fuel Enrichment
Replies: 2
Views: 1277

Re: Launch Control Fuel Enrichment

thanks!
by akep
Wed Apr 22, 2020 3:39 pm
Forum: K-Pro / KManager
Topic: Launch Control Fuel Enrichment
Replies: 2
Views: 1277

Launch Control Fuel Enrichment

I just noticed that Fuel Enrichment under Launch Control changed from % to Units, what units are in reference here? Fuel table units? percent still?

Also, for Ignition Retard, does a positive integer = retard?
by akep
Fri Jul 14, 2017 11:51 pm
Forum: K-Pro / KManager
Topic: Closed Loop Target Lambda only works for v4?
Replies: 5
Views: 2113

Re: Closed Loop Target Lambda only works for v4?

PRB. if i turn it on, it will just correct to 14.7, if i turn it off it follows fuel map. AFCMD stays 14.7 no matter what i change it to.
by akep
Thu Jul 13, 2017 4:51 pm
Forum: K-Pro / KManager
Topic: Closed Loop Target Lambda only works for v4?
Replies: 5
Views: 2113

Re: Closed Loop Target Lambda only works for v4?

the one from parameters > adv closed loop > target lambda low/high button - which brings up the table window for such
by akep
Sun Jul 09, 2017 5:06 pm
Forum: K-Pro / KManager
Topic: Closed Loop Target Lambda only works for v4?
Replies: 5
Views: 2113

Closed Loop Target Lambda only works for v4?

I can't seem to get this v3 to change AFCMD from 14.7 to following Target Lambda tables, I just did it on 3 v4 ecus with success. Help file doesn't mention which version supports it, if different. Am I missing something or is it only a v4 thing?
by akep
Tue Apr 26, 2016 4:59 pm
Forum: K-Pro Calibrations
Topic: Shaky CAM vs CAMCMD and IGN vs Ign table
Replies: 2
Views: 2578

Re: Shaky CAM vs CAMCMD and IGN vs Ign table

thanks i'll look into it
by akep
Mon Apr 25, 2016 7:35 pm
Forum: K-Pro Calibrations
Topic: Shaky CAM vs CAMCMD and IGN vs Ign table
Replies: 2
Views: 2578

Shaky CAM vs CAMCMD and IGN vs Ign table

I've been noticing for a long time on K24A2 swaps, I see what is posted in the images below. Right now the ignition is causing slight drivability issues customer states feels like heistation, During tuning, the shaky VTC angles are causing the fuel/ign tables to flip flop between all tables (0,10, 2...
by akep
Sun Sep 27, 2015 11:55 pm
Forum: K-Pro / KManager
Topic: KPro / KManager requests
Replies: 146
Views: 831642

Re: KPro / KManager requests

i've been wanting to have Ctrl+S for Save As... added to Kmanager for a long long time. I like to save my changes often so I can go back easily or flip flop around when troubleshooting. Also the less I have to use the trackpad to point and click for things the better. or even better, if there could ...
by akep
Sat Dec 14, 2013 1:26 pm
Forum: K-Pro / KManager
Topic: can you connect new version software to old version ecu?
Replies: 10
Views: 5274

Re: can you connect new version software to old version ecu?

i feel like he might have wanted to download his old software off the ecu first... oh well.
by akep
Sat Dec 14, 2013 1:25 pm
Forum: K-Pro / KManager
Topic: Running no o2 Sensors with kpro
Replies: 2
Views: 3522

Re: Running no o2 Sensors with kpro

you should run at least the primary, you gain nothing by running no o2 sensors.
by akep
Sat Dec 14, 2013 2:05 am
Forum: K-Pro / KManager
Topic: VTC phase gap troubleshooting
Replies: 1
Views: 3409

VTC phase gap troubleshooting

Hey guys, So we have a P0341 on a K24A1 ep3. Stock block, revhard mani, t3/t4 turbonetics, nothing special. This kit came off the same owners original K20A3, using the same kal and ecu, when everything was working fine. The kal (one of the revhard base maps for ep3), when all cam angles are set to 0...