Search found 29 matches
- Fri Jul 27, 2007 11:54 am
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
thanks for the reply. Any word as to why I would need to alter the tune on my map after I uploaded it onto another p28 ECU with s300? The firmware was the same, etc.....and I was going from a p28 to a p28. It was very strange, not only did I have to change my fuel multiplier, but I also had to alter...
- Thu Jul 26, 2007 9:58 am
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
- Thu Jul 26, 2007 8:47 am
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
the ecu had the check light error 21 from immediately after I recevied it in the springtime. But since I parked the car from sept to march, I didn't notice the power difference not having vtec. I am embarrassed to say that but the car runs 300ft lbs and my vtec point is 5500rpm so I only lost the fl...
- Thu Jul 26, 2007 6:51 am
- Forum: s300 / SManager
- Topic: attn Hondata: ECU related issue with s300 socketing
- Replies: 7
- Views: 4569
- Wed Jul 25, 2007 5:06 pm
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
Well, I lucked out and found another ecu to test on my car. On the way to get it, I checked mine out again...threw the same spool 21 code. Then I swapped his p28/s300 in the car and the spool error is GONE. The vtec engages like it did last season with my s200 on the same ecu. So my only conclusion ...
- Wed Jul 25, 2007 12:02 pm
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
- Wed Jul 25, 2007 11:21 am
- Forum: s300 / SManager
- Topic: attn Hondata: ECU related issue with s300 socketing
- Replies: 7
- Views: 4569
- Wed Jul 25, 2007 11:16 am
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
well that is bad news. The issue is (if you look at my previous posts on this spool check error) that the error only occurred after I had my ecu prepped with the s300 and boost control by hondata. It is a p28 that was previously socketed for an s200. Immediately after I received the new s300 in my p...
- Wed Jul 25, 2007 9:15 am
- Forum: s300 / SManager
- Topic: vtec spool error issue with s300
- Replies: 11
- Views: 11803
vtec spool error issue with s300
I had a previous issue with the spool error code coming up after I had my ecu socketed by hondata. So I have disabled the spool error check in the newer version of smanager but after putting the car on the dyno I am seeing a torque issue that wasn't there before. It appears that the torque is droppi...
- Sun Apr 29, 2007 1:00 pm
- Forum: s300 / SManager
- Topic: Question regarding launch control/boost control/etc inputs
- Replies: 1
- Views: 1973
Question regarding launch control/boost control/etc inputs
I have been trying a few different things with my s300 and have found the following issues: -using the pinout for the power steering pressure does not work. While datalogging, even with no pin attached, the PSP says ON the entire time. It happens in my buddies s300 also so is this a software glitch?...
- Tue Apr 17, 2007 8:18 am
- Forum: s300 / SManager
- Topic: Boost solenoid mounting location
- Replies: 1
- Views: 2080
Boost solenoid mounting location
As per my other post, I wanted a followup to this question: I originally had my solenoid mounted behind the pass headlight but moved it closer to the wastegate to shorten the vacuum lines to lower boost creep. It seemed to help a bit, but was wondering if mounting the solenoid by the distributor was...
- Mon Apr 16, 2007 11:20 am
- Forum: s300 / SManager
- Topic: Boost control solenoid issue after install
- Replies: 16
- Views: 10948
I originally had it hooked up at the manifold but the problem was identical. I then rerouted the lines to shorten them, and ran the source from the comp housing. Same problem. It seems a little better with a higher spring (ie: 10psi spring versus a 7psi spring), but still creeps more than it previou...
- Sun Apr 15, 2007 12:31 am
- Forum: s300 / SManager
- Topic: Boost control solenoid issue after install
- Replies: 16
- Views: 10948
Boost control solenoid issue after install
I just went from a dual stage manual boost controller to the GM solenoid from hondata with my new s300 (p28). The issue is that while I has very minimal boost creep with rpm increase (2psi increase over 4k-redline)....I am seeing alot of boost creep with the new elec solenoid. I am also noticing int...
- Mon Mar 26, 2007 2:34 pm
- Forum: s300 / SManager
- Topic: attn Hondata: ECU related issue with s300 socketing
- Replies: 7
- Views: 4569
- Mon Mar 26, 2007 12:41 pm
- Forum: s300 / SManager
- Topic: attn Hondata: ECU related issue with s300 socketing
- Replies: 7
- Views: 4569