Search found 14 matches

by freydaddy
Sat Jan 25, 2014 12:45 pm
Forum: HondaLogger Software
Topic: hondata 3 bar MAP sensor values
Replies: 2
Views: 5795

Re: hondata 3 bar MAP sensor values

i set scalar to 617
i set offset to 11
i got the numbers off the internet.
by freydaddy
Sat Jan 25, 2014 12:32 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

I used a new basemap from user hpmx18, and got the air fuel ratio lean 17.2+.
Idles smooth. But now to lean to drive.
how can I get it stoich?
by freydaddy
Sat Jan 25, 2014 12:22 pm
Forum: S300 Calibrations
Topic: need basemap for d16 turbo
Replies: 2
Views: 2606

Re: need basemap for d16 turbo

I just used this basemap on a similar setup, idles really well at 900 rpms.
I went from running rich (12.2:1 a/f) to running low (17.2+:1 a/f).
how can I get the target Lambda to 14.7:1?
by freydaddy
Sun Jan 19, 2014 7:11 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

Lambda is at 12.4:1
injectors are 2.22 ms
wishing some one could show me how to lean it out a little
by freydaddy
Sun Jan 19, 2014 5:34 pm
Forum: HondaLogger Software
Topic: hondata 3 bar MAP sensor values
Replies: 2
Views: 5795

hondata 3 bar MAP sensor values

scalar, offset,
it doesnt give the option for the Hondata MAP sensor.
by freydaddy
Fri Nov 22, 2013 7:39 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

its been a month since I posted the datalog.
does anyone see anything wrong with the calibrations/settings?
by freydaddy
Thu Oct 31, 2013 12:25 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

any intelligent input on this datalog?
by freydaddy
Tue Oct 29, 2013 5:43 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

10.24.13.s3d
datalog
(1.04 MiB) Downloaded 194 times
by freydaddy
Sat Oct 26, 2013 5:07 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

update: everything is close to good on the calibrations. The car idles (950-1000). Lambda reads around 14.7. after it is warmed up then shut off, it will not start until it sits for about 10 minutes. I recorded a datalog for about 3:37 minutes. But I really dont know what im looking at on the graphs...
by freydaddy
Sun Mar 03, 2013 6:26 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

update...Got the 550 cc injectors in. ready to finally drive this to the tuner. starts right up when its cold, 1500 rpms.warms up after about 3-4 minutes, then idles roughly at 850. Then it dies when it is warmed up. Fuel vapors in the garage will burn your eyes. Wideband reads 19. Next I set the in...
by freydaddy
Wed Feb 08, 2012 3:52 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

just an update, i had a bad ect sensor. now replaced.
maybe the whole problem all along.
i will keep you posted when i try to swap the injectors. again.

here is a question...If I run 550 cc injectors without the turbo (na), could i set it for 240 cc with no problems?
by freydaddy
Mon Jan 09, 2012 12:31 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

Re: calibration for swapped injectors

yes it does. I got fed up and replaced the old injectors back just to see if it was something else.
but im not giving up, i need the bigger injectors for the turbo setup.
by freydaddy
Sat Jan 07, 2012 5:50 pm
Forum: S300 Calibrations
Topic: calibration for swapped injectors
Replies: 15
Views: 5514

calibration for swapped injectors

I am having a difficult time trying to get my D16 Honda engine going. I swapped in some new 550 cc injectors (high impedence (13 ohm) in place of the factory 240 cc injectors (12 ohm). I have the s300. I went to the fuel trim tab and changed the injector sizes. Is there something else I need to do?