i set scalar to 617
i set offset to 11
i got the numbers off the internet.
Search found 14 matches
- Sat Jan 25, 2014 12:45 pm
- Forum: HondaLogger Software
- Topic: hondata 3 bar MAP sensor values
- Replies: 2
- Views: 13646
- Sat Jan 25, 2014 12:32 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
I used a new basemap from user hpmx18, and got the air fuel ratio lean 17.2+.
Idles smooth. But now to lean to drive.
how can I get it stoich?
Idles smooth. But now to lean to drive.
how can I get it stoich?
- Sat Jan 25, 2014 12:22 pm
- Forum: S300 Calibrations
- Topic: need basemap for d16 turbo
- Replies: 2
- Views: 4381
Re: need basemap for d16 turbo
I just used this basemap on a similar setup, idles really well at 900 rpms.
I went from running rich (12.2:1 a/f) to running low (17.2+:1 a/f).
how can I get the target Lambda to 14.7:1?
I went from running rich (12.2:1 a/f) to running low (17.2+:1 a/f).
how can I get the target Lambda to 14.7:1?
- Sun Jan 19, 2014 7:11 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
Lambda is at 12.4:1
injectors are 2.22 ms
wishing some one could show me how to lean it out a little
injectors are 2.22 ms
wishing some one could show me how to lean it out a little
- Sun Jan 19, 2014 5:34 pm
- Forum: HondaLogger Software
- Topic: hondata 3 bar MAP sensor values
- Replies: 2
- Views: 13646
hondata 3 bar MAP sensor values
scalar, offset,
it doesnt give the option for the Hondata MAP sensor.
it doesnt give the option for the Hondata MAP sensor.
- Fri Nov 22, 2013 7:39 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
its been a month since I posted the datalog.
does anyone see anything wrong with the calibrations/settings?
does anyone see anything wrong with the calibrations/settings?
- Thu Oct 31, 2013 12:25 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
any intelligent input on this datalog?
- Tue Oct 29, 2013 5:43 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
- Tue Oct 29, 2013 5:39 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
- Sat Oct 26, 2013 5:07 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
update: everything is close to good on the calibrations. The car idles (950-1000). Lambda reads around 14.7. after it is warmed up then shut off, it will not start until it sits for about 10 minutes. I recorded a datalog for about 3:37 minutes. But I really dont know what im looking at on the graphs...
- Sun Mar 03, 2013 6:26 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
update...Got the 550 cc injectors in. ready to finally drive this to the tuner. starts right up when its cold, 1500 rpms.warms up after about 3-4 minutes, then idles roughly at 850. Then it dies when it is warmed up. Fuel vapors in the garage will burn your eyes. Wideband reads 19. Next I set the in...
- Wed Feb 08, 2012 3:52 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
just an update, i had a bad ect sensor. now replaced.
maybe the whole problem all along.
i will keep you posted when i try to swap the injectors. again.
here is a question...If I run 550 cc injectors without the turbo (na), could i set it for 240 cc with no problems?
maybe the whole problem all along.
i will keep you posted when i try to swap the injectors. again.
here is a question...If I run 550 cc injectors without the turbo (na), could i set it for 240 cc with no problems?
- Mon Jan 09, 2012 12:31 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
Re: calibration for swapped injectors
yes it does. I got fed up and replaced the old injectors back just to see if it was something else.
but im not giving up, i need the bigger injectors for the turbo setup.
but im not giving up, i need the bigger injectors for the turbo setup.
- Sat Jan 07, 2012 5:50 pm
- Forum: S300 Calibrations
- Topic: calibration for swapped injectors
- Replies: 15
- Views: 9184
calibration for swapped injectors
I am having a difficult time trying to get my D16 Honda engine going. I swapped in some new 550 cc injectors (high impedence (13 ohm) in place of the factory 240 cc injectors (12 ohm). I have the s300. I went to the fuel trim tab and changed the injector sizes. Is there something else I need to do?