Search found 10 matches

by ex-r-wagon
Sun Jun 01, 2014 11:07 am
Forum: s300 / SManager
Topic: solid red light on s300 at time of start up?
Replies: 8
Views: 6136

Re: solid red light on s300 at time of start up?

A further update. I updated Smanager to version 2.3.3.0 and opened my current calibration file. I uploaded the file to the S300 and the green light came on (red light out). Car starts and runs as normal. I can data log (red light blinking). As soon as I turn the car off and then try to start the car...
by ex-r-wagon
Sun Jun 01, 2014 10:11 am
Forum: s300 / SManager
Topic: solid red light on s300 at time of start up?
Replies: 8
Views: 6136

Re: solid red light on s300 at time of start up?

Interesting. I have just had the same thing happen with my S300 (ser# S300-13053). P72 ecu running a built all motor H22A. Car ran fine all Thursday (multiple starts and stops). Go to start it up Friday evening, "Check Engine" light, stumbles and idles very rough (like it's in limp mode). ...
by ex-r-wagon
Sat Sep 08, 2012 7:52 pm
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Default values set. Will test and monitor for the next week to see if that eliminates the CEL code 1.
by ex-r-wagon
Thu Sep 06, 2012 8:27 pm
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Any useful data in the log file or do I need to be capturing another file with the check engine light coming on.
by ex-r-wagon
Sat Aug 25, 2012 4:31 pm
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Here is an additional log file of the problem. This file may be a better file to look at. The CAL file is the same as the one posted above. The "Check Engine" light comes on at 6minutes, 42 seconds into the log.
by ex-r-wagon
Mon Aug 20, 2012 1:18 pm
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Finally captured a log. When I was logging the CEL would not come on. As soon as I was not logging the CEL would come on (Murphy's Law).
by ex-r-wagon
Mon Jul 23, 2012 11:09 am
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Latest version of software is now installed. I will post a new log as soon as I can. Thank you.
by ex-r-wagon
Sun Jul 22, 2012 4:25 pm
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Update: For one week I have been using the "Narrow Band" signal from the PLX O2 sensor. No CEL so far. I will now change back to the "Wide Band" signal to see if the CEL light comes back on. Does the log file contain any useful information that might indicate the cause of the CEL...
by ex-r-wagon
Sat Jul 14, 2012 3:07 pm
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

Re: CEL code 1

Log of CEL code 1 and the CAL file. Engine is an H22A, sleeved, 12:1 pistons, Eagle "H" beam rods, BC Stage II N/A cams and BC flat stainless valves, 94 octane pump gas.
by ex-r-wagon
Wed Jul 11, 2012 10:12 am
Forum: s300 / SManager
Topic: CEL code 1
Replies: 11
Views: 2611

CEL code 1

I have P72 manual ECU with S300 v1 installed (ser# 13053). I get CEL code 1 randomly coming on while driving (does not seem to be related to driving style or engine temp). I have a PLX wideband SM-AFR with a DM6 gauge. In the Parameters setup under 'Options' both Closed Loop operation and Disable O2...