Hondata

Hi. That was just a comparison to what it shows when cold started, and idling.. 650 mBar upwards is way too high.. she wants to flood herself to death. Yes I understand that that reading, 935 mBar at WOT is fully normal. I just do not get why she is so high when cold, and if I cannot get this under ...

Hey all. i have a problem and i hope to find help here. My MAP Sensor is reading too high, causing the ecu to squirt too much fuel, to the point of the engine bogging out. The engine is not t/c'd or s/c'd. I have tried a multitude of things: Exchanged MAP sensor for a new one (OEM), reverted t/b's f...

Damned me!! Looking at what you just posted, i saw it right away... why not earlier?? Alright, sorry and thanks at the same time..

Mounty

Hi one and All. PlX DM-6 is installed. have o2, oiltemp, oil press, water temp sensors installed. Placed the gauge in my sungalss 'cubby' atop, by the maplights, along with a killswitch/start button. Spunkster: Is it possible to change the info in the Helpfile?? Under Wideband/ECU connections it say...

Hello again, Spunkster, Sir. Have been on further 'recon' about connecting the o2 Sensor/Controller. I sifted through the WDM's and found these... from what it looks like, the ELD is hardwired into my ECU, meaning: a) I could cap the wire at the fusebox (out/BLU-BLK or 'x30').... this continues as &...

Beautiful, Perfect!!! Thank you, Sir!! Ordered myself a small batch.
Be warned: I may have questions during the install....
Mounty/Markus

I see, yes, to adapt/connect further o2 sensors.. doh.. would you happen to know where ecu pins are sourceable?? I know from oemaruraparts(dotcom) that you have to buy the whole harness, which i need not.
Mounty

Hi Spunkster, just a heads up: If you buy the whole 'kit/set' with the o2 sensor, they send a cable kit along too, and from what it looks like, there are ecu/obdii connector pins included...

Mounty

http://www.plxdevices.com/Wideband-O2-A ... 002726.htm

Ok, thanks first off!!
One, hopefully last question: which input would you recommend? De/Repinning E15 (ELD) or just Pinning new into one of the B's?? (Unused atm)... the wire set with the plx has 'pins'... i believe you recommend using these/this product??
Again, Regards
Mounty

Yessir, affirmative. Have it, the wideband helpfile, printed out and laying infront of me. I understand (correctly???) that i need the ELD pin location for the input. Being, in my case, a tsx/euro accord, the E connector on the ECU, Pin E15. OK, roger that... but, why does the 'ECU Connectors' link/...

Yes sir, understand that, and have a PLX controller ordered. I am still stuck as to how to connect it. I have found ELD on Plug "E". So ground it to the t/b, i/m ground?? Thanks for all your help. Spunkster, for all my questions. Good service!!
Regards
Mounty

Hello Sirs; i have a few questions about connecting yet another o2 sensor, for On-the-street-tuning/pre-adjustment before going dyno... I have 2 new, 1 OEM Honda, and 1 Bosch sensor. They are the 'heated' type, so where do i hook them up to regulate the heating/voltage draw so the signal/measurement...

Ok, new (used) ecu and bnib FP ordered from Heel-toe... have the old FP w. oem packaging, just no longer have the ecu.. no not where it is... tis a long story.. i shit you not!!! Can I send the "old" FP back to you for resetting now?? I would like to "give" it to a young forum bu...

Can I have the old one sent to you for resetting??
Thanks

Hi, I have not been around for a while, have had some major motor issues: It has now been rebuilt the 3rd and hopefully last time. Along the way, with all the motor removals/installs, my ECU for an 07-08 TSX has gone lost... what I have now (no idea where this came from.... more than likely, HH) is ...