Search found 59 matches
- Tue May 26, 2015 1:22 pm
- Forum: K-Pro / KManager
- Topic: grounding the cyl head
- Replies: 3
- Views: 1346
Re: grounding the cyl head
Yeap that's it. I see that it connects at the cyl valve cover stud BUT where does the other end connect to (g101)?
- Tue May 26, 2015 1:18 pm
- Forum: K-Pro Calibrations
- Topic: k20a basemap or equivelent
- Replies: 4
- Views: 2930
Re: k20a basemap or equivelent
The only k20a map i see in the new calc menu is a modified map, and it is not in the pnf menu. No base maps for the k20a.
- Tue May 26, 2015 10:23 am
- Forum: K-Pro Calibrations
- Topic: k20a basemap or equivelent
- Replies: 4
- Views: 2930
Re: k20a basemap or equivelent
Is a k20a3 OK to start base tuning with?
- Tue May 26, 2015 8:23 am
- Forum: K-Pro / KManager
- Topic: grounding the cyl head
- Replies: 3
- Views: 1346
grounding the cyl head
Where is G101 located (so I can ground properly) on the 02 civic si wiring harness??? Thanks a million!
- Mon May 25, 2015 9:24 am
- Forum: K-Pro Calibrations
- Topic: k20a basemap or equivelent
- Replies: 4
- Views: 2930
k20a basemap or equivelent
i need a base map for a k20a, i cant find anything close on the "new calibration" menu. is it possible to use a basemap for a k20a2 or k20a3 to get it started up? i would prefer the k20a original basemapping but i cant dig one up anywhere. thanks a million in advance!!
- Wed May 20, 2015 6:24 pm
- Forum: s300 / SManager
- Topic: nitrous triggrer input?
- Replies: 5
- Views: 1888
Re: nitrous triggrer input?
That information is incorrect, it is -12 volt (ground) by default, inverted it is +12 volt. Good it has the option to invert input or i would have been running another wire from the engine bay.
- Mon Mar 30, 2015 1:07 pm
- Forum: s300 / SManager
- Topic: input switch datalogging
- Replies: 5
- Views: 2325
Re: input switch datalogging
I know its been 2years since I first posted this but I've never been able to trigger the data logging feature of my s300. I have a toggle switch connected to negative ground, then going to the correct pin on the ecu. Should I maybe have a momentary switch instead of a toggle?
- Mon Mar 30, 2015 11:07 am
- Forum: s300 / SManager
- Topic: nitrous triggrer input?
- Replies: 5
- Views: 1888
Re: nitrous triggrer input?
OK, is that a 12v positive OR negative input by default?
- Mon Mar 30, 2015 10:07 am
- Forum: s300 / SManager
- Topic: nitrous triggrer input?
- Replies: 5
- Views: 1888
nitrous triggrer input?
I want to hookup nitrous on my 93 prelude with s300 (white board) installed on p75 odb1 ecu. I will be using the a/c switch pin (b5) . Is it possible to use the switch in the dash with its existing wiring to trigger "ARM", if I simply set the nitrous input in the smanager to b5, Or do I ha...
- Tue May 20, 2014 10:44 am
- Forum: s300 / SManager
- Topic: AN1(D12 pin) input ethanol content anylizer
- Replies: 15
- Views: 5014
Re: AN1(D12 pin) input ethanol content anylizer
Oh and the analog output of the Zeitronix eca display is linear and proportional to the output of the flex fuel sensors signal. Only difference is it has been internally "pulled up" inside the eca to 0-5v. I believe the the correct hookup if you have the eca display and still want to use i...
- Tue May 20, 2014 9:48 am
- Forum: s300 / SManager
- Topic: AN1(D12 pin) input ethanol content anylizer
- Replies: 15
- Views: 5014
Re: AN1(D12 pin) input ethanol content anylizer
No I did not they my spare ecu because when I opened it up I seen someone had altered it, rendering it broken for now. I did not try the d10 pin because when reading instructions u seen it says remove OR replace with 1n4038 diode. The key was "or" I think it means "and". So it sw...
- Mon May 19, 2014 9:12 pm
- Forum: s300 / SManager
- Topic: AN1(D12 pin) input ethanol content anylizer
- Replies: 15
- Views: 5014
Re: AN1(D12 pin) input ethanol content anylizer
OK, so I've had no success getting the analizer to read properly so I'm going to upgrade to the white board s300. Now my question is before I do it, I see the white board wants the direct wire coming from the flex fuel sensor and a 2.4k ohm resister installed between the 12v pos wire and the sensor ...
- Thu May 15, 2014 9:04 am
- Forum: s300 / SManager
- Topic: AN1(D12 pin) input ethanol content anylizer
- Replies: 15
- Views: 5014
Re: AN1(D12 pin) input ethanol content anylizer
Its a Rywire direct jumper harness. It it just a extra length for cutting and splicing into if need be just like stock harness. I purchased directly from Rywire. I have it on a 1993 Honda prelude si 2.3ltr. Sorry I should have been more informative, probably spooked ya when I said jumper harness. Ma...
- Wed May 14, 2014 5:21 pm
- Forum: s300 / SManager
- Topic: AN1(D12 pin) input ethanol content anylizer
- Replies: 15
- Views: 5014
Re: AN1(D12 pin) input ethanol content anylizer
I have the zetronics hooked to d12 pin. The output from the zetronics is outputting about .4 of a volt since I have low content enthonal fuel rite now. So yes there is voltage being applied abd read by my fluke multimeter in the vid i attached, I have my jumper harness cut at pin d12 and the zetroni...
- Wed May 14, 2014 3:13 pm
- Forum: s300 / SManager
- Topic: AN1(D12 pin) input ethanol content anylizer
- Replies: 15
- Views: 5014
Re: AN1(D12 pin) input ethanol content anylizer
You lost me a little. You mean the large harness that plugs directly into the s300? Why would those inputs have a output? I have my gauges wired to those inputs so I can datalog. Im confused on where to check that voltage at you are asking for.