Search found 79 matches

by Carchitect
Thu Jun 19, 2014 6:46 pm
Forum: s300 / SManager
Topic: s300 knock sensor with a p28. analog input possible?
Replies: 3
Views: 2699

Re: s300 knock sensor with a p28. analog input possible?

Is there a method of switching to the newer non-resonance wide range knock sensors. The ones with the thru 8mm hole? I have a method of fastening it to the engine but the output characteristics are different between the narrow range 1 wire knock sensors and the newer 2 wire knock sensors. The 1 wire...
by Carchitect
Thu Jun 19, 2014 6:31 pm
Forum: s300 / SManager
Topic: T1 cam tigger for hondata
Replies: 3
Views: 3700

Re: T1 cam tigger for hondata

T1 cam trigger uses a dual output hall sensor. The sensor uses 4 wires. Power, ground, hall 1 and hall 2. Hall 1 output happens when a north pole of a magnet passes over it. Hall 2 output happens when a south pole of a magnet passes over it. The honda distributor uses 3 sensors. TDC, CYP (also known...
by Carchitect
Sat Dec 13, 2008 12:49 pm
Forum: s100/s200
Topic: s200 twincharged civic dyno sheet...
Replies: 4
Views: 5027

With a GT45 you should be able to pull off 1200 hp but for that I'm sure the motor would require rework.

Do you have any more pictures of your work?
by Carchitect
Sun Aug 24, 2008 9:29 pm
Forum: Non-Hondata
Topic: AEM Engine Position Sensor
Replies: 4
Views: 9499

The OEM dizzy uses a mag reference sensor. It produces a wave pattern sorta like a heartbeat in other words its a simple high to low or low to high trigger. It produces its own current/voltage. The triggers is what the ecu is looking for. The TDC uses 1 trigger per revolution. Since the cam turns at...
by Carchitect
Sun Aug 24, 2008 6:35 pm
Forum: Romeditor 4 Software
Topic: G-sensor and 2nd ignition trigger question.
Replies: 1
Views: 7013

G-sensor and 2nd ignition trigger question.

I have the G-sensor installed in my S200. Will it still be supported in RomEditor 4? If so I may be upgradng to it or going the S300 route. Also I plan on adding triggers on the OEM cam gears and simulate TDC and CYL position sensor inouts for the ecu and add the OBD-2 oil pump and CKF sensor for CR...
by Carchitect
Sun Apr 08, 2007 10:26 am
Forum: s300 / SManager
Topic: Apex boost solenoid in place of GM solenoid
Replies: 4
Views: 3384

Apex boost solenoid in place of GM solenoid

Will I be able to use the Apex boost solenoid instead of the Gm solenoid? The solenoid is a better quality unit. It has wires and I can repin it to use OEM honda/sumitomo connectors. The housing is a metal unit and most guys have reviewed it to function very well. http://www.horsepowerfreaks.com/vie...
by Carchitect
Sun Jan 29, 2006 2:27 pm
Forum: s300 / SManager
Topic: Hondata S300 Nightmare (Updated--Nightmare no more)
Replies: 37
Views: 18165

Aman, you have a better way of fixing your IAB issue w/o a relay. On you 99 GSR the IAB solenoid connector will have two wires. One will be a Black and the other will be Red with a Blue stripe. As mentioned above the ECM control is reversed. The logical thing for anyone would be to install a relay b...
by Carchitect
Fri Nov 04, 2005 2:03 pm
Forum: s300 / SManager
Topic: Questions for Hondata
Replies: 10
Views: 5491

I've figures out what I'm going to do for it. My goal is to use the greddy e-manage ultimate to control the four channel ignition duties. It has the capability of taking the cam,crank sensors and igniter command in and spitting out four outputs for individual spark output. I intend to use this outpu...
by Carchitect
Thu Sep 01, 2005 11:04 am
Forum: s300 / SManager
Topic: Questions for Hondata
Replies: 10
Views: 5491

BTW, does the S300 use a lambda wide band input for tuning only or does it keep it there and make its necessary adjustments? In other words does it work in open/closed loop using the OEM 4-wire sensor or does it work is full loop using a wide band controller's lambda output?

Thanks in advance

Joe.
by Carchitect
Wed Aug 31, 2005 9:44 pm
Forum: s300 / SManager
Topic: Questions for Hondata
Replies: 10
Views: 5491

Questions for Hondata

I know you have a lot going on but if you can chime in I would would really appreciate it. My S200 has been working wonderfully but I wish I could say the same about the ignition system. Quite frankly I've had it with the distributor and would really like to switch to a 4 channel M&W ignition PRO-14...
by Carchitect
Wed Aug 31, 2005 9:32 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11021

Its good to see that you've got the thing working but 10.X:1 is way too rich and can easily wash out the rings and loose compression and flood the engine. You really need to tie the wideband into the o2 input and select the appropriate sensor lambda selection. This will enable the software to read t...
by Carchitect
Tue Jan 18, 2005 12:36 pm
Forum: s100/s200
Topic: buying used hondata S100
Replies: 1
Views: 1535

The only units that datalog today are the S200 units. If you were to purchase the S100 the dealer will need to use his/her datalog enabled S200 box to tune your car and then assemble your ecu with the S100. The S100 unit keeps your ecu self contained just like having someone make a custom program fo...
by Carchitect
Sun Aug 01, 2004 4:42 pm
Forum: s100/s200
Topic: vortech b16 tuning
Replies: 2
Views: 1715

I've tuned a 99 si with the aftercooled vortech kit using the 10 psi vortech pulley and belt. The car has an MSD 6a with blaster ss coil,dc 4-1 header,deleted cat,720 greddy injectors, vortech fuel rail, 6an fittings and hose from the stock fuel filter to rail and a vortech fuel optimizer installed ...
by Carchitect
Wed Jun 23, 2004 8:14 pm
Forum: s100/s200
Topic: 1000cc injectors controlled by hondata
Replies: 12
Views: 6032

Once you get over 600 cc you really NEED a good spray pattern to get the fuel to atomize right for proper idle and good driveability. I just recently tuned a turbocharged type-R w/1000 cc injectors. Idle is at 1000 primarily since this car has a lot of stereo equipment in it and I didn't want the li...
by Carchitect
Wed Jun 02, 2004 11:15 am
Forum: s100/s200
Topic: A few Qs for the Hondata guys
Replies: 4
Views: 1914

Well. Moderators? anyone?

Joe H.