Search found 24 matches

by phoenix5
Thu Apr 23, 2015 6:21 am
Forum: K-Pro / KManager
Topic: questions/concerns about extra wires inside Koro ecu
Replies: 5
Views: 1448

Re: questions/concerns about extra wires inside Koro ecu

Adjusting gear comp made shifts a lot better. while driving this morning, I had the problem arise again, and was able to repeat it over and over. I noticed my temp was above 200, and my tps wasn't reading at the lower level where the throttle is barely open. Under those conditions the car would acce...
by phoenix5
Wed Apr 22, 2015 5:58 am
Forum: K-Pro / KManager
Topic: questions/concerns about extra wires inside Koro ecu
Replies: 5
Views: 1448

Re: questions/concerns about extra wires inside Koro ecu

Some ideas that may be cause are lean protection, tip-in, and or gear comp.
by phoenix5
Wed Apr 22, 2015 5:55 am
Forum: K-Pro / KManager
Topic: is this a bug in KManager? tip-in, stock knock. etc
Replies: 23
Views: 4522

Re: is this a bug in KManager? tip-in, stock knock. etc

What type of TPS are you using? Just throwing an idea out there, the TPS may have a worn section in the resistor pad that could cause it to read wrong, which could cause this.
by phoenix5
Tue Apr 21, 2015 8:24 am
Forum: K-Pro / KManager
Topic: questions/concerns about extra wires inside Koro ecu
Replies: 5
Views: 1448

Re: questions/concerns about extra wires inside Koro ecu

i did not mean to solely place blame on the ecu. I did not think the fuel gauge signal came from the ecu, however I thought it may be a symptom of failing sender unit or questionable fuel pump assembly, or water corrosion in the connectors or wiring. - 2002 Honda Civic DX - Modifications that may af...
by phoenix5
Sun Apr 19, 2015 10:07 pm
Forum: K-Pro / KManager
Topic: questions/concerns about extra wires inside Koro ecu
Replies: 5
Views: 1448

questions/concerns about extra wires inside Koro ecu

I was looking at images of kpro ecus and I noticed that none of the images I saw had extra wires soldered on the board. I'm concerned that my ecu could be crippled from a loose wire. I've never put much thought into it until recently when I blew a motor and replaced it with another and had similar i...
by phoenix5
Fri Sep 12, 2014 7:02 am
Forum: K-Pro Calibrations
Topic: Question ? KAL
Replies: 1
Views: 1503

Re: Question ? KAL

Im no authority but there is several calibrations included with kmanager when you install it. They are in the 'c:\program files\kmanager\calibrations' folder. I think there is a calibration made for the same mods in there. The calibrations are all labeled plainly.
by phoenix5
Fri Sep 12, 2014 6:58 am
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

Im hopefully not breaking any rules by saying im also on k20a.org and clubrsx under the same username I have on this board. I've switched back to the stock tune for the time being.
by phoenix5
Fri Sep 05, 2014 12:22 am
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

I appreciate the feedback. I understand. Could someone send me a calibration based on my mods? I would be interested in a separate map geared solely towards fuel efficency in a daily driven, stop and go scenario. I throw newspapers every night for a living. I drive about 90 to 100 miles per day. If ...
by phoenix5
Mon Aug 25, 2014 5:26 pm
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

The new hall effect tps is great. I still have that noise though, perhaps a valve lash adjustment will solve that.

I plan to drop the intake cam of a k20z3 in my head when I adjust the valve lash. Is there a recommendation for a different calibration?


Idle fluctuations were due to vacumn leak.
by phoenix5
Tue Aug 19, 2014 8:42 am
Forum: K-Pro Calibrations
Topic: CIVIC CTR EU K20A2 good map for CAI/catback ?
Replies: 1
Views: 2322

Re: CIVIC CTR EU K20A2 good map for CAI/catback ?

Its what im using and its been working since I got my kpro. Very similar mods. Every car is different and I honestly know next to nothing about tuning but my engine hasnt exploded yet. And I go full throttle and go redline fairly often. I really dont think I have much to complain about as far as mid...
by phoenix5
Tue Aug 19, 2014 8:34 am
Forum: K-Pro Calibrations
Topic: Euro EP3 Stock Calibration.
Replies: 4
Views: 2381

Re: Euro EP3 Stock Calibration.

Are you sure you have k20a2 and not k20a or k20a3? If you are sure you have k20a2, and if its anything like the usa k20a2 then you dont have itr cams. Theres probably not much difference between a2 cams and itr cams but there is some, and you could be running leaner or richer and you could have diff...
by phoenix5
Tue Aug 19, 2014 8:23 am
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

List of mods: Magnaflow bolt on catback exhaust for 03 type s Injen sri hybrid racing 74mm throttle body, intake manifold port matched Ktuned ep3 pulley (power steering deleted) have ep3 steering rack but unplugged Hasport billet kswap mounts with 70a bushings Otherwise afaik it is a stock 2003 rsx ...
by phoenix5
Tue Aug 19, 2014 7:50 am
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

I have a theory that it could be related to my tps by chance, on most of the datalogs I saw knock when there was sudden variation in the tps, where I remember seeing it in the log was at higher rpm between gear shifts but my tps seems to cause the worst problems at low part throttle, it will buck a ...
by phoenix5
Mon Aug 18, 2014 5:45 pm
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

Spunkster wrote:I highly recommend you get this professionally dyno tuned.
I believe there is a dyno nearby but I feel like its geared towards domestics, but I guess I could give them a call. I would really like to learn to tune it myself...
by phoenix5
Mon Aug 18, 2014 5:43 pm
Forum: K-Pro Calibrations
Topic: request help reviewing/tuning k20a2
Replies: 11
Views: 3851

Re: request help reviewing/tuning k20a2

I have two other extended datalogs but something refuses to let me upload them, one is over 8mb.