Search found 8646 matches

by Hondata
Wed Oct 23, 2019 7:10 am
Forum: General / Traction Control Manager Software
Topic: Hondata flashpro question
Replies: 1
Views: 5

Re: Hondata flashpro question

1. Did you read this?
https://www.hondata.com/help/flashpro/v ... ocking.htm
You can unlock and use of other vehicles, but only one at a time.

2. You can return the ECU back to stock.
by Hondata
Tue Oct 22, 2019 12:21 pm
Forum: K-Pro / KManager
Topic: Kpro usb and can output errors
Replies: 1
Views: 22

Re: Kpro usb and can output errors

Sounds like it is not datalogging at all. What KPro do you have, what are the lights on the KPro doing and does KManager show with the ignition on? I'll also shortcut to the most common problem on the S2000 which is forgetting to attach the harness ground on the end of the cylinder head, almost unde...
by Hondata
Tue Oct 22, 2019 8:58 am
Forum: Civic 2016+ 1.5 Turbo Americas/Asia
Topic: Change AFM calibration voltage values to optimize
Replies: 3
Views: 108

Re: Change AFM calibration voltage values to optimize

I would not add or remove any of the voltage index values.
by Hondata
Mon Oct 21, 2019 7:47 am
Forum: Civic Type R 2015+
Topic: turbo spooling suddenly sounds super loud, a leak? but boost reads ok.....
Replies: 3
Views: 53

Re: turbo spooling suddenly sounds super loud, a leak? but boost reads ok.....

You have a leak and the turbo is over speeding. The wastegate goes from 2.5mm to under 1mm later in the datalog.

Don't boost until you fix this as turbo overspeed is very bad.

I would also fix the P0136 error since that is easy to fix.
by Hondata
Sat Oct 19, 2019 7:12 pm
Forum: S300 Calibrations
Topic: HELP! car leans when lights go on
Replies: 8
Views: 101

Re: HELP! car leans when lights go on

Multiple problems. Your charging system is not good. The voltage should not dip to under 12V just putting the lights on. The lambda seems incredibly rich even with the lights off; under 12:1 at idle. IAT is high (125F). This will tend to make things rich anyhow. Do you have a hot air intake? Why no ...
by Hondata
Sat Oct 19, 2019 7:08 am
Forum: Civic Type R 2015+
Topic: p0136 p0139
Replies: 27
Views: 2018

Re: p0136 p0139

There is a checkbox "P0136 ... error enabled". If you check it, then the error is enabled. If you uncheck it, then the error is disabled. I'm not sure how to make it clearer.

In any case with V3.4.7 you have the mother of all DTC disable lists (600 DTCs).
by Hondata
Fri Oct 18, 2019 7:07 am
Forum: Civic 2016+ 1.5 Turbo Americas/Asia
Topic: 2020 Si Unknown?
Replies: 1
Views: 64

Re: 2020 Si Unknown?

We are making a release today for that part number.
by Hondata
Wed Oct 16, 2019 9:08 pm
Forum: Applications
Topic: KPRO MANAGER WILL NOT INSTALL USB DRIVER
Replies: 14
Views: 4624

Re: KPRO MANAGER WILL NOT INSTALL USB DRIVER

Do you have a KPro plugged in? If not, then you don't need the driver. If so, give more information.
by Hondata
Wed Oct 16, 2019 11:12 am
Forum: FlashPro Manager
Topic: FlashProManager 3.4.7
Replies: 1
Views: 151

FlashProManager 3.4.7

V3.4.7 (18 Oct 2019) FlashPro firmware updated to version 169 [2016+ Turbo Civic Si] Added part number 5AM-A221 to supported list V3.4.6 (17 Oct 2019) [2009 Civic Si]Fixed locking V3.4.5 (15 Oct 2019) FlashPro firmware updated to version 168 Fixed automatic calibration update process [2015-2017 FK2 ...
by Hondata
Wed Oct 16, 2019 6:31 am
Forum: Applications
Topic: Confirmation of what the CAM angle real means
Replies: 6
Views: 106

Re: Confirmation of what the CAM angle real means

More or less.

If the intake cam is at 30, all it means is that it is 30 crank degrees advanced over the base (locked) position.
by Hondata
Wed Oct 16, 2019 6:29 am
Forum: Civic Type R 2015+
Topic: Altitude and Boost Consideration
Replies: 10
Views: 1660

Re: Altitude and Boost Consideration

The 'turbo max ratio (temp)' uses IAT2. I'll check the table tracing is correct.

IAT2 = in the AFM before the turbo.

IAT = in the manifold.
by Hondata
Mon Oct 14, 2019 7:55 pm
Forum: Civic 2016+ 1.5 Turbo Americas/Asia
Topic: Change AFM calibration voltage values to optimize
Replies: 3
Views: 108

Re: Change AFM calibration voltage values to optimize

Yes, the table index (voltage) is used in the table lookup.
by Hondata
Mon Oct 14, 2019 7:54 pm
Forum: Applications
Topic: Confirmation of what the CAM angle real means
Replies: 6
Views: 106

Re: Confirmation of what the CAM angle real means

You're asking for the cam opening and closing angles. We do not have that information.
by Hondata
Mon Oct 14, 2019 2:56 pm
Forum: Civic Type R 2015+
Topic: Altitude and Boost Consideration
Replies: 10
Views: 1660

Re: Altitude and Boost Consideration

PA = 82 kPA and I'm guessing about 5% loss through to the turbo, so the turbo sees around 78 kPa. Picking 4000 rpm the IAT PR table is 3.13, so the turbo will be restricted to 244 kPa. Actual BP cmd at this point 243 kPa (and I did not cheat). So it is the turbo max ratio (temp) table. Increase by 0...