Search found 48 matches

by bian.yy
Wed Apr 18, 2018 5:27 pm
Forum: TSX 2004-2014
Topic: Tplate table issue on 08 at
Replies: 4
Views: 1621

Re: Tplate table issue on 08 at

If the AT controller uses throttle pedal to determine shift points, then by changing the table you're effectively getting more pedal for the same plate position, so the AT controller thinks there is more load, and shifts later. I understood your statement. Your statement is the guess from phenomeno...
by bian.yy
Wed Apr 18, 2018 2:09 am
Forum: TSX 2004-2014
Topic: Tplate table issue on 08 at
Replies: 4
Views: 1621

Re: Tplate table issue on 08 at

Let's see if Mr .Hondata or Spunkster can have a look on this issue or not?
by bian.yy
Sat Apr 14, 2018 4:41 pm
Forum: TSX 2004-2014
Topic: Tplate table issue on 08 at
Replies: 4
Views: 1621

Tplate table issue on 08 at

Hi Hondata After I read this link I feel mine is the same issue like s2000. https://www.hondata.com/forum/viewtopic.php?f=29&t=19370&p=97093#p97093 when I change low throttle pedal area from 1:1 to 1:0.45 for better traffic Jam smooth driving, car shift from 1st to 2nd at 3000+ RPM with very light t...
by bian.yy
Fri Apr 13, 2018 12:56 am
Forum: FlashPro Manager
Topic: What exactly does tplate % represent in datalogs?
Replies: 68
Views: 13279

Re: What exactly does tplate % represent in datalogs?

The S2000 is the only vehicle we've seen using the additional index table. The US 06 Si and FN2 don't use that table but the throttle table index has changed like the S2000. FN2 table: fn2-th.png I'm not sure why Honda has scaled to table in such a way for the S2000. It almost is like a mix up in u...
by bian.yy
Wed Oct 04, 2017 4:58 am
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Jerky shift daily drive
Replies: 3
Views: 1291

Re: Jerky shift daily drive

Hi HD
I tested your cal it didnt help. I put cut rpm to 3000 it get more better for low speed go and stop driving.
Do you have any other reminder?
by bian.yy
Tue Oct 03, 2017 4:08 pm
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Jerky shift daily drive
Replies: 3
Views: 1291

Re: Jerky shift daily drive

Hi Hondata

If I am using vtc table to control decel, do I need to set column 1 and 2/1250RPM up to a proper degree or just leave it with 0 as is.
I will try this map and feedback you. thank you very much.
by bian.yy
Mon Oct 02, 2017 5:59 am
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Jerky shift daily drive
Replies: 3
Views: 1291

Jerky shift daily drive

Hi Hondata My car is stock 14 SI. Could you check why my daily driving shift are very jerky. 1 throttle release on gear 1 and 2 suddenly brake the car, I have already tuned slightly injector cutoff with a little help only. 2 injection time when clutch pedal pressed varies refer to unstable Tplate. M...
by bian.yy
Sun Sep 03, 2017 8:24 pm
Forum: FlashPro Manager
Topic: How can I get column 10 activated on fuel table
Replies: 6
Views: 779

Re: How can I get column 10 activated on fuel table

Yes, I am living 1345 ft. So I don't need to care about column 10 then.
by bian.yy
Fri Sep 01, 2017 4:51 pm
Forum: FlashPro Manager
Topic: How can I get column 10 activated on fuel table
Replies: 6
Views: 779

Re: How can I get column 10 activated on fuel table

If the air pressure is not high enough or you have intake restriction then you will not reach column 10. This is normal. Ok, I understand, because of my intake is still stock, do you have any experience if I change to CAI for higher flow will it obviously decrease low end torque from 1000 to 3000?
by bian.yy
Thu Aug 31, 2017 10:05 pm
Forum: FlashPro Manager
Topic: How can I get column 10 activated on fuel table
Replies: 6
Views: 779

How can I get column 10 activated on fuel table

Hi Hondata

How can I get my column 10 of delta fuel table activated during road tuning WOT. I am already push down to floor, you can look on tplate data.
Setup is K24A2 + 421 header.
by bian.yy
Tue Jun 06, 2017 6:21 pm
Forum: TSX 2004-2014
Topic: IDLE papameter issue it did not take effect.
Replies: 12
Views: 2740

Re: IDLE papameter issue it did not take effect.

Spunkster wrote:
Thu May 18, 2017 3:03 pm
Have you tried the idle learn procedure?

With the engine completely warm and everything turned off (ac, audio, lights, etc.), let the car idle for 5 minutes without touching the throttle. IF the fans come on, do not include the time they are on in the 5 minutes.
Is there any update?
by bian.yy
Mon May 22, 2017 2:09 pm
Forum: TSX 2004-2014
Topic: IDLE papameter issue it did not take effect.
Replies: 12
Views: 2740

Re: IDLE papameter issue it did not take effect.

Have you tried the idle learn procedure? With the engine completely warm and everything turned off (ac, audio, lights, etc.), let the car idle for 5 minutes without touching the throttle. IF the fans come on, do not include the time they are on in the 5 minutes. I followed it please check the datal...
by bian.yy
Thu May 18, 2017 10:59 pm
Forum: TSX 2004-2014
Topic: IDLE papameter issue it did not take effect.
Replies: 12
Views: 2740

Re: IDLE papameter issue it did not take effect.

Please refer the 10 minute idle datalog.
by bian.yy
Thu May 18, 2017 4:24 am
Forum: TSX 2004-2014
Topic: IDLE papameter issue it did not take effect.
Replies: 12
Views: 2740

Re: IDLE papameter issue it did not take effect.

Could you check why this setting dosenot work, I need this function to be fixed.my car is automation tranny.
by bian.yy
Mon Mar 20, 2017 3:21 pm
Forum: TSX 2004-2014
Topic: IDLE papameter issue it did not take effect.
Replies: 12
Views: 2740

Re: IDLE papameter issue it did not take effect.

Spunkster wrote:What year vehicle is this and what exactly has been done to it?
05tsx stock plus 07 flashpro.