Is there a way to repair the output, or to know which components were damaged? Or will it require a new ecu.
Otherwise I will need to run the fan from a manual switch.
Search found 91 matches
- Tue Apr 28, 2020 9:43 am
- Forum: s300 / SManager
- Topic: A12 FANC not sending signal
- Replies: 6
- Views: 1314
- Mon Apr 27, 2020 6:07 pm
- Forum: s300 / SManager
- Topic: A12 FANC not sending signal
- Replies: 6
- Views: 1314
Re: A12 FANC not sending signal
The relay I had on it was bad and I replaced it. So I’m guessing that it damaged the output then.
- Mon Apr 27, 2020 2:10 pm
- Forum: s300 / SManager
- Topic: A12 FANC not sending signal
- Replies: 6
- Views: 1314
Re: A12 FANC not sending signal
Yes I am using a relay. I tested for a signal at the relay and also at the ecu and I got nothing.
It has worked okay for years and just suddenly stopped.
It has worked okay for years and just suddenly stopped.
- Mon Apr 27, 2020 1:26 pm
- Forum: s300 / SManager
- Topic: A12 FANC not sending signal
- Replies: 6
- Views: 1314
A12 FANC not sending signal
I have been using my s300v3 in a p28 to control my fan via A12 signal from the ecu. Recently I am getting no voltage output from A12 even when Hondata shows that FANC is active. Any ideas what to check? I updated the software and when trying to update USB drivers I get an error that it failed to upd...
- Wed Jun 26, 2019 9:17 am
- Forum: s300 / SManager
- Topic: Tuning fuel injector shutoff/overrun
- Replies: 5
- Views: 4044
Re: Tuning fuel injector shutoff/overrun
Well my tuning laptop is not able to get online at the moment, so I have no way to upload the tune quickly. BUT, I think I have gotten the problem under control. I adjusted the fuel overrun cutoff TPS to 0%, and the delay at 250ms. I increased the load values to 9, 9, 11, 12, 18. It seems to have do...
- Mon Jun 24, 2019 12:59 pm
- Forum: s300 / SManager
- Topic: Tuning fuel injector shutoff/overrun
- Replies: 5
- Views: 4044
Re: Tuning fuel injector shutoff/overrun
And I will record datalog tomorrow and post it up. Thanks again.
- Mon Jun 24, 2019 12:58 pm
- Forum: s300 / SManager
- Topic: Tuning fuel injector shutoff/overrun
- Replies: 5
- Views: 4044
Re: Tuning fuel injector shutoff/overrun
Thanks for these suggestions. I may have not worded what I said correctly when I said I adjusted the TPS setting. I meant in the fuel cutoff/overrun table it has a value to set below what % throttle the injectors turn off at. What should this be set at? I would just put it at 0% but I fear the throt...
- Sun Jun 23, 2019 8:13 am
- Forum: s300 / SManager
- Topic: Tuning fuel injector shutoff/overrun
- Replies: 5
- Views: 4044
Tuning fuel injector shutoff/overrun
I've been battling issues with severe jerkiness when my injector shut off and turn back on under light throttle conditions, for example at my work campus I drive pretty far staying at low rpm in 1st and 2nd gear to stay under 15mph, and in doing so the injector will occasionally shut off make my car...
- Sun Aug 12, 2018 8:20 am
- Forum: s300 / SManager
- Topic: S.Trim Freezing
- Replies: 6
- Views: 2338
- Thu Aug 09, 2018 7:04 pm
- Forum: s300 / SManager
- Topic: S.Trim Freezing
- Replies: 6
- Views: 2338
Re: S.Trim Freezing
39275
2.6.6.0
2.6.6.0
- Thu Aug 09, 2018 3:15 pm
- Forum: s300 / SManager
- Topic: S.Trim Freezing
- Replies: 6
- Views: 2338
S.Trim Freezing
I’ve had this problem quite a few times now, normally after a longer highway drive. I’ll stop at a stoplight and notice my AFR go lean. I check my s.trim on my phone and it will be stuck at some random number, today was 1.56%. I made it home but it wasn’t adjusting s.trim anymore and my AFR was very...
- Mon Jul 02, 2018 12:48 pm
- Forum: s300 / SManager
- Topic: Cylinder Fuel Trim
- Replies: 4
- Views: 1777
Re: Cylinder Fuel Trim
Alrighty. It runs just fine with them at 0% so I will leave it like that for now. When I go for a dyno tune I will have my injector data sheet handy and discuss with the tuner.
Thanks,
Thanks,
- Mon Jul 02, 2018 9:37 am
- Forum: s300 / SManager
- Topic: Cylinder Fuel Trim
- Replies: 4
- Views: 1777
Re: Cylinder Fuel Trim
I tried it. Didn't really notice any difference in the vibration, must be unrelated.
But back to my question, is it proper practice to adjust cylinder trims to try and match the injectors, or should the trims be left at 0%?
But back to my question, is it proper practice to adjust cylinder trims to try and match the injectors, or should the trims be left at 0%?
- Fri Jun 29, 2018 3:40 am
- Forum: s300 / SManager
- Topic: Cylinder Fuel Trim
- Replies: 4
- Views: 1777
Cylinder Fuel Trim
When I took ownership of my car, it had the cylinder fuel trim settings as follows: Cylinder #1 - 0% Cylinder #2 - 2% Cylinder #3 - 2% Cylinder #4 - 0% My instincts were to leave the settings alone as much as possible as they should have been input by the previous tuner. However now I am questioning...
- Fri Jun 29, 2018 3:33 am
- Forum: s300 / SManager
- Topic: Target Lambda table
- Replies: 4
- Views: 1719
Re: Target Lambda table
I thought these were controlled by going to Options > Settings > Target Lambda
The closed loop advanced parameters control what your wideband will try to actually adjust to when driving in closed loop.
The closed loop advanced parameters control what your wideband will try to actually adjust to when driving in closed loop.