Search found 45 matches

by JDMLyfeStyle
Sun Aug 27, 2006 12:16 am
Forum: s300 / SManager
Topic: Question about ECU wiring.. for Drag car
Replies: 4
Views: 2251

i do have the manual for the car. i have all the wiring diagrams for it.

But i wanted to ask hondata what are the crucial wires i should pay attention to so that Nothing will affect how the ECU opporates.
by JDMLyfeStyle
Fri Aug 25, 2006 4:29 pm
Forum: s300 / SManager
Topic: Question about ECU wiring.. for Drag car
Replies: 4
Views: 2251

well the stock harness is too much of a mess to diagnose when you have a electrical issue.. better to go through the wires goin right off the ECU to the engine.. that rip apart the whole interior and find a issue. so thats why i was asking hondata what pins are needing the straight 12v and good grou...
by JDMLyfeStyle
Thu Aug 24, 2006 11:36 pm
Forum: s300 / SManager
Topic: Question about ECU wiring.. for Drag car
Replies: 4
Views: 2251

Question about ECU wiring.. for Drag car

Well ive decided to turn my hatch into a Full Drag car. i will be running my S300 Ecu I need to know what is NEEDED for the ECU to properly work. Everything is going off a relay and fuse board. I plan to have all wires off the ECU run directly to engine sensors. Sheilding all sensors to prevent any ...
by JDMLyfeStyle
Thu Aug 24, 2006 3:51 pm
Forum: s300 / SManager
Topic: service connector question
Replies: 5
Views: 2369

if you want the light to appear on the gauge cluster. Why not wire a light to something less important. such as the Seatbelt light.
by JDMLyfeStyle
Sat Aug 19, 2006 9:11 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

lol i dunno its just driving me nuts.. No breaks in any of the wires. everything is getting proper voltage and power I have 2 92 EG's both wired for vtec. ones bone stock and the other is swapped Swapped car.. a Chipped ECU will work. But the S300 will not. Stock car... S300 works and so does the ch...
by JDMLyfeStyle
Wed Aug 16, 2006 11:50 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

Ok so tonight I tried a Chipped ECU and the car runs fine on the Chipped ECU.. So there is no problem with the Car picking up the external ROM.. i wonder why it will not pick up on the S300.. Ive tried the Original version 1-06 1-0-9 1-1-5 1-1-6 and Non of those versions can i run th car for more th...
by JDMLyfeStyle
Tue Aug 15, 2006 3:16 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

The Fuel Pump is on a kill switch but it is not getting its signal from the ECU. Hot off Battery through a Relay and to a hidden switch. The ECU does attempt to datalog. logs RPM's for 1 second when it tries to run. peak RPM's is 549 RPM's so far. Havent looked to see if it shows the Injectors Firin...
by JDMLyfeStyle
Tue Aug 15, 2006 12:39 am
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

well i went a rechipped a ECU for S300 to make sure there was no issues. Now when i put the S300 into my BONE STOCK CX. and open up the P28 BIN everything runs Fine. BUt when i put it into His car 92 CX with b16 swap the car wont even start. Car has a UNTOUCHED wiring harness. nothing is CUT. Stock ...
by JDMLyfeStyle
Fri Aug 11, 2006 6:05 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

I am going to try to put in a socket and chip in there to see if it works. and i will try to datalog with my old setup and if all that comes out well i will be definately sending the ECU and S300 to you. I just want to get every single test and possiblity out of the way before i send it out because ...
by JDMLyfeStyle
Fri Aug 11, 2006 1:24 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

All the Pins are seated correctly. the Height of the pins has not been alter'd at all. The S300 is sitting on all the pins correctly Also if there was a grounding issue with the ECU then how would the ECU still run if the J1 Jumper was removed? I took the board and the hondata to a local computer sh...
by JDMLyfeStyle
Thu Aug 10, 2006 9:35 pm
Forum: s300 / SManager
Topic: Suggestions for use laptop for S300?
Replies: 9
Views: 4571

im running a toshiba 512MB ram 1.6ghz. bought it off ebay for $140 shipped
by JDMLyfeStyle
Thu Aug 10, 2006 9:26 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

If all the lights are working on the board. and the files upload and it Attempts to datalog could there be a problem with it sending tht info to the board. cause im looking at the ECU Board right now and there are no lifted tracks that i can realy see.. just a few scratches in the protective coating...
by JDMLyfeStyle
Thu Aug 10, 2006 8:19 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

The ECU was just shipped to you to chip. he did not send the hondata unit with it. I just went outside 5 mins ago and i cut the J1 Jumper to convert it back to stock and the car fired right up and runs perfectly fine. I think it might be a bad board. The car setup is b16a2 block Overbored P30 piston...
by JDMLyfeStyle
Thu Aug 10, 2006 6:29 pm
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 10902

My hondata S300 Daughter board FRIED???

Posting for a Friend This ECU has under 30 minutes of Use i had my ECU resocketed by hondata cause i thought i might have messed up somewhere. So i get the ECU back and i install the daughterboard and when i start my car it immediately dies. So i reupload a ROM using the Current 1.6 Version Now if i...
by JDMLyfeStyle
Fri Aug 04, 2006 4:37 am
Forum: s300 / SManager
Topic: S300 and S200 got a question about them
Replies: 3
Views: 1885

any specific reasons why not? I think it would be a nice thing to have.. go to a tuner use S300 then save file and burn to S100 or S200