Search found 11 matches

by CRVTEC0WNZJ00
Tue Nov 01, 2005 10:19 pm
Forum: s300 / SManager
Topic: CRVTEC Ignition Timing problems with S300
Replies: 2
Views: 2263

CRVTEC Ignition Timing problems with S300

Checking timing on my engine after taking care of some wiring and some other mechanical details. Anyway, car is a 1993 Honda Civic Si with a CR/VTEC engine. The details in short are B20B4 block with JE 11:5:1 pistons and other lower end internals and a stock 2000 ITR head with bolt ons like throttle...
by CRVTEC0WNZJ00
Sun Oct 02, 2005 2:02 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

Irrelivent I was fixing all the little things that went wrong and more things went wrong like had to swap out the t-mount that I was told to buy that didn't fit for the right one, we basically fabbed up a t-mount and yadayada, now waiting on shift linkage and shit it accidentally got bent, the thing...
by CRVTEC0WNZJ00
Wed Aug 31, 2005 10:06 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

I've got friends that know how to tune it they just havn't been able to help me yet, plus I'm in Indiana and there is only one shop here that I know of well enough that has a dyno...but I don't want to go there. As for the hook up of the O2 sensor its a PLXM300 and its wired how it says to wire it t...
by CRVTEC0WNZJ00
Tue Aug 30, 2005 7:31 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

Engine is in the car, got it running too on my own with no help on the tuning aspect!!! But the A/f ratio is 10.X:1 at idle at around 1000rpm...going to ask how to pull some fuel because some of the fuel table numbers confuse me alittle :?
by CRVTEC0WNZJ00
Wed Aug 24, 2005 11:04 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

I'm quite curious why there isn't a 2.0L basemap from hondata directly considering LS/VTEC and CR/VTEC builds are pretty damn popular...
by CRVTEC0WNZJ00
Tue Aug 23, 2005 10:23 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

why is it that hondata admin hasn't replied to this yet... :?
by CRVTEC0WNZJ00
Tue Aug 23, 2005 12:37 am
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

I don't know...but I put in that I had 440CC injectors over the stock 280's or 220's whatever the stock ones are...I used a JDM P72 from 92-95 as the starting point...and I turned up overal fuel correction like 3% because I'll be running probably 50psi at idle...but I don't think these look very saf...
by CRVTEC0WNZJ00
Mon Aug 22, 2005 7:15 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

Okay, I'll unhook the VAFC. However I was told I could run a JDM P30 ECU Map to start and scale it to 2.0L....however I see no place in the software to scale up displacement.
by CRVTEC0WNZJ00
Mon Aug 22, 2005 4:22 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

Anyone....? 30 views and one reply...
by CRVTEC0WNZJ00
Mon Aug 22, 2005 9:54 am
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

DutchEG6 wrote:dump that Apexi V-AFC when you got the hondata
I'm not going to use the VAFC for anything except rev's and sensor checks because its already installed and I'll just leave it. How about a post that is actually helpful. :wink:
by CRVTEC0WNZJ00
Sun Aug 21, 2005 9:46 pm
Forum: s300 / SManager
Topic: Base map for CR/VTEC EG Swap
Replies: 16
Views: 11053

Base map for CR/VTEC EG Swap

I need some suggestions about the base map setup for Hondata S300. I have yet to do the swap but should be this upcoming weekend pending all the little stupid things that could screw me have shown up. Well heres what I'm using. I need suggestions about IGNITION TIMING AND FUEL AS WELL AS FUEL PRESSU...