Search found 58 matches

by Shmaa
Sun Jul 27, 2008 2:36 pm
Forum: s300 / SManager
Topic: Upgrading 1.26 to 1.37
Replies: 1
Views: 1386

Upgrading 1.26 to 1.37

I will probably be upgrading here soon.

I need to know if there will be any significant changes that may affect the way the car runs (default/new compensation values etc). Or if there are any features I may need to turn on or off.

Thanks
by Shmaa
Sat May 03, 2008 1:45 pm
Forum: s300 / SManager
Topic: Boost Control / Solenoid Problem
Replies: 2
Views: 1975

Well I pulled off the boost solenoid and when I disconnected the vacuum line quite a bit of water came out.... Not sure how that happened and the main vacuum line going to the wastegate was dry...

Have yet to confirm if this is the issue
by Shmaa
Wed Apr 30, 2008 7:50 pm
Forum: s300 / SManager
Topic: Boost Control / Solenoid Problem
Replies: 2
Views: 1975

Boost Control / Solenoid Problem

I have been running the integrated boost control since it was released. I use the GM boost solenoid and have it configured to low boost = spring pressure ~10psi, high boost = 15psi(normally achieve this with 25% duty). The car has been sitting for approx 8 months, but it has been driven occasionally...
by Shmaa
Wed Apr 02, 2008 8:17 pm
Forum: s300 / SManager
Topic: SManager V1.3.4
Replies: 22
Views: 13020

Yes...
by Shmaa
Tue Apr 01, 2008 7:01 pm
Forum: s300 / SManager
Topic: SManager V1.3.4
Replies: 22
Views: 13020

Whats the status on the expanded lambda conversion table?
by Shmaa
Wed Jan 23, 2008 4:11 pm
Forum: s300 / SManager
Topic: SManager V1.3.0
Replies: 16
Views: 10556

Thank You, I appreciate the response.
by Shmaa
Tue Jan 22, 2008 8:42 pm
Forum: s300 / SManager
Topic: SManager V1.3.0
Replies: 16
Views: 10556

Less it not more when it comes to customer service...Did you just decide not to answer part of my question? Is it not physically possible to add more points for the conversiontable?
by Shmaa
Mon Jan 21, 2008 10:02 pm
Forum: s300 / SManager
Topic: SManager V1.3.0
Replies: 16
Views: 10556

I have a wideband with a non-linear output and currently use around 8 conversion points for a really good reading. Is there not enough room onboard to hold the extra data points that used to be available? My wideband works great and it would be nice to use my hardware to its potential.
by Shmaa
Fri Apr 06, 2007 12:36 pm
Forum: s300 / SManager
Topic: New to Hondata
Replies: 10
Views: 4594

Spunkster wrote:You have to use the Nitrous/AUX parameters for this.
What?
by Shmaa
Sat Mar 31, 2007 11:13 am
Forum: s300 / SManager
Topic: Smanager and Win2k
Replies: 6
Views: 3562

I used to use it on Win2k. Nothing different needed to be done, but this was a while ago with previous versions. I cannot say for sure with the newest version.
by Shmaa
Thu Mar 29, 2007 3:49 pm
Forum: s300 / SManager
Topic: Smanager and Win2k
Replies: 6
Views: 3562

SManager, has worked with 98, 2K etc. just fine.

They just dont support it.
by Shmaa
Sun Feb 18, 2007 12:20 am
Forum: s300 / SManager
Topic: Boost Control Manual A/C Switch
Replies: 8
Views: 5140

Ok, I understand. You usually are switching the input to ground, so the power for any light in a switch will need come come from the vehicle, not the ECU.

You have a power and a ground and a load.

makes LED's do this

Image
by Shmaa
Mon Feb 05, 2007 3:56 pm
Forum: s300 / SManager
Topic: popping at idle
Replies: 17
Views: 9171

40-42 is pretty good, pull the vacuum off of the fpr and check it, I try to keep mine a litte under 50psi. if it is only doing it occasionally you can probably just richen up the idle a tad and that should take care of it. Before I got a fpr my fuel pressure was over 60psi and I had to run like 12.5...
by Shmaa
Fri Feb 02, 2007 11:20 pm
Forum: s300 / SManager
Topic: popping at idle
Replies: 17
Views: 9171

I have seen several cars do the same thing and each time it was because the fuel pressure was too high. With the walbro and the stock FPR the fuel pressure will go up somewhere around 60psi and with injectors as large as the 750's the pulse speed at idle is so low that it causes these pops.
by Shmaa
Tue Jan 30, 2007 9:44 pm
Forum: s300 / SManager
Topic: popping at idle
Replies: 17
Views: 9171

What fuel pump do you have and what is your fuel pressure?