Search found 20 matches

by Spanky
Sat Dec 01, 2007 2:34 pm
Forum: S300 Calibrations
Topic: need base map for NA mild build ls/vtec
Replies: 1
Views: 2856

thats a very similar set up to what im running. the only difference is im running a type r head with bc iv cams, with stock injectors @ 50 psi fuel pressure. Im running a modified b18c5 type r base map with a plx m300 wide band o2. Its a good starting point.
by Spanky
Thu Mar 22, 2007 3:14 pm
Forum: s300 / SManager
Topic: No diag/ and no rev launch
Replies: 3
Views: 1893

yes i have. several times. down loaded newest version twice.
by Spanky
Thu Mar 22, 2007 1:12 pm
Forum: s300 / SManager
Topic: No diag/ and no rev launch
Replies: 3
Views: 1893

No diag/ and no rev launch

i have a little problem with my s300. ive had it over a year, and WAS working great. heres the prob...i just finished some upgrades. did have a stock b17a1 running off of a wideband plx m300. what i did, added ctr pistons and buddyclub iv cams/springs. problem started when i went with the crower cal...
by Spanky
Mon Mar 19, 2007 6:02 pm
Forum: s300 / SManager
Topic: two problems when street tuning..
Replies: 8
Views: 3976

please post calibration. i would like to compare to my own d series settings. same as yours except i used a to4e 60 trim. and i ran 22 psi
by Spanky
Wed Feb 21, 2007 7:07 pm
Forum: S300 Calibrations
Topic: D16Z6 Turbo calibration ?
Replies: 1
Views: 2611

buy a wide band o2 sensor/controller. your new best friend. idle will be your biggest trick, but closed loop takes care of itself. you shouldnt go any leaner than 12.8:1 on 93 octane, especially on a stocker. as timing goes, 12-14 degrees atdc is easiest on your bearings, although you could make a f...
by Spanky
Wed Feb 21, 2007 7:00 pm
Forum: S300 Calibrations
Topic: Need S300 Calibrations for my D16Y8.
Replies: 2
Views: 2851

i started with the p28 base map.
by Spanky
Wed Feb 21, 2007 6:57 pm
Forum: S300 Calibrations
Topic: P28 D16Z6 Calibration = correct ?!
Replies: 6
Views: 4754

do you have the latest version of s300? i ran 22lbs of boost on a d16y8 daily starting from that basemap. for your idle, play with the iacv settings. you can also play with the cold start, but i find that you really do not need to. what error code do you have? make sure that the light in your s300 i...
by Spanky
Wed Feb 21, 2007 6:53 pm
Forum: S300 Calibrations
Topic: Tune needed.....Stock GSR with bolt-ons???
Replies: 2
Views: 3487

the gsr cams dont have enough lift. thats why your car falls off at high rpms. the intake can only deliver air quicker at high rpm, you need that air to get into the cylinder. higher lift camsought to do the trick! :wink:
by Spanky
Mon Mar 06, 2006 9:17 pm
Forum: s300 / SManager
Topic: gm 3barmapsenser
Replies: 20
Views: 10989

Here is how to calculate the scalar and offset. 1. Find the minimum and maximum voltage and absolute pressures. 2. Convert the pressures to mbar. 3. Subtract the minimum and maximum voltages to find the range, then do the same for the pressures. 4. Divide the pressure range by the voltage range to c...
by Spanky
Sun Mar 05, 2006 5:32 pm
Forum: s300 / SManager
Topic: gm 3barmapsenser
Replies: 20
Views: 10989

try 669 scalar and -334 offset.
by Spanky
Wed Jan 04, 2006 8:01 pm
Forum: s300 / SManager
Topic: create boost tables will not save
Replies: 1
Views: 1629

create boost tables will not save

when i enter the create boost and ignition tables feature under EDIT i cannot get s300 to save. it constantly goes back (after clicking ok) to no change on ignition retard and dont change for fuel change under boost. what gives????
by Spanky
Fri Dec 23, 2005 8:02 pm
Forum: s300 / SManager
Topic: Stolen
Replies: 3
Views: 3066

that completely blows! those thieves should be hung by their man berries
by Spanky
Wed Dec 21, 2005 7:16 pm
Forum: s300 / SManager
Topic: both red and green light on inside ecu
Replies: 5
Views: 3458

i let my girlfriend borrow my laptop, until friday. I will do all of this and get back 2 you. thanks alot!
by Spanky
Sat Dec 17, 2005 12:43 pm
Forum: s300 / SManager
Topic: both red and green light on inside ecu
Replies: 5
Views: 3458

no, but when i show my display, i get like 56000 rpm, crazy numbers. pure tunung installed my s300. first week end after the new year im just gonna drive there and dyno tune. when the car idles everything is fine. as soon as i hit the gas, looneyville.
by Spanky
Thu Dec 15, 2005 6:40 pm
Forum: s300 / SManager
Topic: both red and green light on inside ecu
Replies: 5
Views: 3458

car runs and drives ok.