Search found 20 matches
- Sat Dec 01, 2007 2:34 pm
- Forum: S300 Calibrations
- Topic: need base map for NA mild build ls/vtec
- Replies: 1
- Views: 3252
- Thu Mar 22, 2007 3:14 pm
- Forum: s300 / SManager
- Topic: No diag/ and no rev launch
- Replies: 3
- Views: 2255
- Thu Mar 22, 2007 1:12 pm
- Forum: s300 / SManager
- Topic: No diag/ and no rev launch
- Replies: 3
- Views: 2255
No diag/ and no rev launch
i have a little problem with my s300. ive had it over a year, and WAS working great. heres the prob...i just finished some upgrades. did have a stock b17a1 running off of a wideband plx m300. what i did, added ctr pistons and buddyclub iv cams/springs. problem started when i went with the crower cal...
- Mon Mar 19, 2007 6:02 pm
- Forum: s300 / SManager
- Topic: two problems when street tuning..
- Replies: 8
- Views: 5114
- Wed Feb 21, 2007 7:07 pm
- Forum: S300 Calibrations
- Topic: D16Z6 Turbo calibration ?
- Replies: 1
- Views: 3056
buy a wide band o2 sensor/controller. your new best friend. idle will be your biggest trick, but closed loop takes care of itself. you shouldnt go any leaner than 12.8:1 on 93 octane, especially on a stocker. as timing goes, 12-14 degrees atdc is easiest on your bearings, although you could make a f...
- Wed Feb 21, 2007 7:00 pm
- Forum: S300 Calibrations
- Topic: Need S300 Calibrations for my D16Y8.
- Replies: 2
- Views: 3352
- Wed Feb 21, 2007 6:57 pm
- Forum: S300 Calibrations
- Topic: P28 D16Z6 Calibration = correct ?!
- Replies: 6
- Views: 5892
do you have the latest version of s300? i ran 22lbs of boost on a d16y8 daily starting from that basemap. for your idle, play with the iacv settings. you can also play with the cold start, but i find that you really do not need to. what error code do you have? make sure that the light in your s300 i...
- Wed Feb 21, 2007 6:53 pm
- Forum: S300 Calibrations
- Topic: Tune needed.....Stock GSR with bolt-ons???
- Replies: 2
- Views: 4213
- Mon Mar 06, 2006 9:17 pm
- Forum: s300 / SManager
- Topic: gm 3barmapsenser
- Replies: 20
- Views: 13303
Here is how to calculate the scalar and offset. 1. Find the minimum and maximum voltage and absolute pressures. 2. Convert the pressures to mbar. 3. Subtract the minimum and maximum voltages to find the range, then do the same for the pressures. 4. Divide the pressure range by the voltage range to c...
- Sun Mar 05, 2006 5:32 pm
- Forum: s300 / SManager
- Topic: gm 3barmapsenser
- Replies: 20
- Views: 13303
- Wed Jan 04, 2006 8:01 pm
- Forum: s300 / SManager
- Topic: create boost tables will not save
- Replies: 1
- Views: 1982
create boost tables will not save
when i enter the create boost and ignition tables feature under EDIT i cannot get s300 to save. it constantly goes back (after clicking ok) to no change on ignition retard and dont change for fuel change under boost. what gives????
- Fri Dec 23, 2005 8:02 pm
- Forum: s300 / SManager
- Topic: Stolen
- Replies: 3
- Views: 3742
- Wed Dec 21, 2005 7:16 pm
- Forum: s300 / SManager
- Topic: both red and green light on inside ecu
- Replies: 5
- Views: 4221
- Sat Dec 17, 2005 12:43 pm
- Forum: s300 / SManager
- Topic: both red and green light on inside ecu
- Replies: 5
- Views: 4221
- Thu Dec 15, 2005 6:40 pm
- Forum: s300 / SManager
- Topic: both red and green light on inside ecu
- Replies: 5
- Views: 4221