Search found 17 matches

by 94vt3c
Wed Feb 19, 2020 3:39 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Any other ideas to troubleshoot? I'm stumped here..
by 94vt3c
Tue Feb 18, 2020 7:38 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Same result. No sensor detected on digi input.
by 94vt3c
Tue Feb 18, 2020 3:52 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

I will check it when I get home from work. Question though why would that affect it? Flex sensor has been installed since I got the kpro and is functioning properly.
by 94vt3c
Tue Feb 18, 2020 2:11 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Absolutely nothing. Parked it working fine. Sat for a few days then my current predicament happened.
by 94vt3c
Tue Feb 18, 2020 1:14 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Unfortunately no..
by 94vt3c
Tue Feb 18, 2020 12:41 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Yes. Tried a few known good calibrations
by 94vt3c
Tue Feb 18, 2020 12:07 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Nothing changed. Just battery was low voltage and it struggled to start. Started on the 2nd try and boom no sensor detected. Ethanol content has been setup for a long time
by 94vt3c
Mon Feb 17, 2020 7:25 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Sorry digital connection looks wrong in the first photo. Here is a better look with it disconnected. Again shotty wiring is temp.
by 94vt3c
Mon Feb 17, 2020 7:02 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Please forgive the shotty wiring, this is only temporary until I find the problem. Last photo is the placement of the old PLX.
by 94vt3c
Mon Feb 17, 2020 4:31 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Update: Brand new PLX installed. Analog working Digital still not working to KPRO.... No Sensor Detected
by 94vt3c
Wed Feb 12, 2020 3:21 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Just ordered a new plx complete. Will update after install
by 94vt3c
Wed Feb 12, 2020 12:59 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

I forgot to say the analog input is reading signal but not displaying A/F . When hooked up digital the Digital 0 read a flat 10.0 as well as the A/F. With Analog connected A/F sits at 14.70. Does nothing with throttle change. Analog 0 reads around 13.90 at idle and has changes with throttle.
by 94vt3c
Tue Feb 11, 2020 6:51 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Connected to analog. Changed parameters to configure analog. Analog is reading signal but not nearly as good as the digital used to before this issue.
by 94vt3c
Sun Feb 09, 2020 1:11 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

The only thing I can think of is it's the KPro board. Like I said the wideband reads fine on it's own. All wiring is the same and w as s working for over 6 months. The car runs fine. Kpro can still make adjustments to fuel maps parameters etc. I think something is wrong with the digital input. Any i...
by 94vt3c
Sat Feb 08, 2020 2:15 pm
Forum: K-Pro / KManager
Topic: PLX Stopped communicating
Replies: 29
Views: 869

Re: PLX Stopped communicating

Waiting for PLX devices to look over the test data of their controller and get back to me. From what I see it seems to function properly. Here's the test instructions they sent as well as the results. Instructions: Ok. There are some tests we can do.  First have the SM-AFR get power direct off batte...