Search found 10 matches
- Tue Dec 16, 2014 6:01 am
- Forum: s300 / SManager
- Topic: wont prime
- Replies: 3
- Views: 1901
Re: wont prime
fuel pump capacitors need replacing. a quick fix is to cut wire A7 on the harness (Fuel pump) and ground the wire (harness side not ecu side). This will make the fuel pump be on all the time. it will not turn on and shut off. i ran several ecus like this with no problems.
- Tue Oct 14, 2014 4:35 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1521879
Re: SManager software requests
is it possible to have a rolling anti lag/2 step launch control for tx2k/mile racing? need to stop brake boosting to create boost while rolling. If you have 2-step set up as always on, I would try to wire in a push button switch and put it inline with your speed sensor signal wire to the ecu. When ...
- Thu Oct 09, 2014 4:38 am
- Forum: s300 / SManager
- Topic: Full throttlle shift
- Replies: 16
- Views: 13062
Re: Full throttlle shift
No you should wire in a clutch switch and then feed the signal from the switch to one of the inputs at the ECU. If you dont do that then your FTS rpm will be your rev limitrev hard wrote:o ok..and how do you set it up? ''always on'' ? does that use the clutch then?
- Wed Oct 08, 2014 10:39 am
- Forum: s300 / SManager
- Topic: Full throttlle shift
- Replies: 16
- Views: 13062
Re: Full throttlle shift
You stay in boost with FTS. I did a quick datalog and with FTS i was able to stay in boost between shifts. I did a 2nd gear pull with FTS into 3rd gear. Car was at 14PSI in 2nd gear and only dropped back down to 8psi in between shifts. before i would loose all boost. With street tires i was just spi...
- Sun Oct 05, 2014 7:10 am
- Forum: s300 / SManager
- Topic: Full throttlle shift
- Replies: 16
- Views: 13062
Re: Full throttlle shift
Bumpppp. Spunkster is hondata looking into having FTS active only after the car is moving. A lot of us need our launch control rpm set higher than our FTS rpm. The way hondata is setup now this is not possible. Can you guys look into this for the next update. If we can have an option to have FTS act...
- Wed Oct 01, 2014 2:16 pm
- Forum: s300 / SManager
- Topic: Full throttlle shift
- Replies: 16
- Views: 13062
Re: Full throttlle shift
Spunkster can you please add a mph enable feature for FTS. Or have launch control take precedence over fts at 0mph? We can't rev higher than fts rpm with clutch pushed in at 0mph
- Mon Sep 29, 2014 10:26 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1521879
Re: SManager software requests
For full throttle shift, can you have a setting so that it is active after a certain speed? I am trying to set my 2-step launch control rpm higher than the FTS rpm and i cant do it. My launch rpm must always be lower than my FTS rpm in order to have both working. So what i want to end up running is ...
- Tue Jun 10, 2014 4:45 am
- Forum: FlashPro Manager
- Topic: Random CEL - 3K Rev Limit
- Replies: 2
- Views: 2146
Re: Random CEL - 3K Rev Limit
FYI disabling "Mass or volume circuit range performance problem enabled (P0101)" fixed the problem
- Mon Jun 09, 2014 5:42 am
- Forum: FlashPro Manager
- Topic: Random CEL - 3K Rev Limit
- Replies: 2
- Views: 2146
Random CEL - 3K Rev Limit
2007 SI just got tuned and everything was running good but after driving around the car for a few minutes it would throw a CEL and the rev limit would be stuck at 3K. I didnt check to see what the code was but i heard that i need to do the following: Can someone confirm... will not get a chance to g...
- Sat Mar 11, 2006 11:05 pm
- Forum: s100/s200
- Topic: Moates BURN1 chip burner
- Replies: 1
- Views: 2235
Moates BURN1 chip burner
if u have a tuned .bin map, can u burn the program using a moates BURN1 chip burner? Im new to hondata but i've been using uberdata for a while now. also im using sst27ST512 EEPROM chips. anyoneused them with hondata?