Search found 31 matches

by Bflaker
Mon Jun 15, 2009 6:55 am
Forum: K-Pro / KManager
Topic: Problem datalogging A/F with AEM UEGO
Replies: 5
Views: 3309

Thanks for the lack of help, but I fixed it on my own. Switched the AEM to output voltage in the range of 1-2 volts, and then made the proper adjustments in Kpro. It reads and datalogs fine now.
by Bflaker
Tue Jun 09, 2009 12:07 pm
Forum: K-Pro / KManager
Topic: Problem datalogging A/F with AEM UEGO
Replies: 5
Views: 3309

So why is the A/F flat-lining in K-Pro at 12.04 ? The AEM gauge itself displays the A/F fine on it's own display, all the way down to 10.0 A/F. I guess I could stick a volt meter on the wire and see what voltage is being sent to the ELD pin when the A/F flatlines. Seems like whenever I ask a questio...
by Bflaker
Tue Jun 09, 2009 4:28 am
Forum: K-Pro / KManager
Topic: Vtec upper/lower boundary K20A3?
Replies: 6
Views: 1800

Wait, so you have a K20a3 in your mini, not a K20a2?

*OFF TOPIC* Where are you located? That mini looks freakin' awesome!!
by Bflaker
Tue Jun 09, 2009 4:25 am
Forum: K-Pro / KManager
Topic: Problem datalogging A/F with AEM UEGO
Replies: 5
Views: 3309

Problem datalogging A/F with AEM UEGO

Here's my setup: AEM UEGO Wideband with the white wire going to the ELD pin on the ECU. Voltage offset is: -0.3 Voltage Calibration is: 0 volts = 10.0 A/F 5 volts = 20.0 A/F I've been messing around with my car getting the All Motor tune dialed in before I start spraying the nitrous again, and I not...
by Bflaker
Sun May 24, 2009 9:27 pm
Forum: K-Pro / KManager
Topic: fuel cutoff during tip in of throttle
Replies: 9
Views: 4002

I've been trying to figure out this problem for a while now. I've also noticed that Kpro rounds the TPS on mine as well. I wish someone would figure this out, cause now that I have Innovative Billet 75A's, the jerkiness is exxagerated drastically.
by Bflaker
Fri Mar 13, 2009 5:37 am
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

Hondata1 wrote:For tuning at AF ratios under 11.5 you should use an aftermarket wideband as the stock AF sensor was designed for the sort of AF ratios seen in a NA car. I wouldn't trust the stock SF sensor readings for tuning my nitrous.
Thank you very much sir.
by Bflaker
Thu Mar 12, 2009 12:32 pm
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

Hummm.....I've installed six AEM UEGO's and never had a single problem with a single one. I guess I've been lucky. You still didn't answer my question about the stock wideband and how low it can read. I understand you say it's the most reliable, but if it only reads to 11.5, it makes it difficult to...
by Bflaker
Mon Mar 09, 2009 9:07 pm
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

If you're planning to use an aftermarket wideband, I would HIGHLY recommend using the PLX. Is there a reason why you recommend them? Also, what about the factory o2 not reading below 11.5? I have never been able to datalog below 11.4 @ WOT, but a few other people have posted that they can read to 1...
by Bflaker
Fri Mar 06, 2009 7:17 am
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

If you go on ebay right now, you can find the Innovative and AEM widebands for $199 shipped. I'm not sure which one I want though. I've installed countless AEM UEGO's so I'll probably just stick with that one.
by Bflaker
Thu Mar 05, 2009 8:08 am
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

I've never been able to datalog mine at anything below 11.4 when tuning my nitrous. It just flatlines and stays at 11.4.

Can someone from Hondata verify this?
by Bflaker
Wed Mar 04, 2009 8:22 pm
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

http://www.hondata.com/kpro.html Scroll down to General Notes. 8) They specifically state 11.5. One thing still has me a lil' confused though. When you go into Help in Kmanager, and pull up the Closed Loop Settings, it shows a box that you can check that is called "Datalog ELD Voltage". When I go un...
by Bflaker
Wed Mar 04, 2009 12:48 pm
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

Nope, it can only read to 11.5. This was quoted directly from Hondata's description of K-PRO. "The stock JDM and US O2 sensor is wide band and can read from 11.5:1 to 30:1 A/F ratios." So basically, all I have to do is run the output from the Wideband gauge to the ELD pin on the ECU and I'll be able...
by Bflaker
Wed Mar 04, 2009 6:51 am
Forum: K-Pro / KManager
Topic: new to kpro, please help wideband question
Replies: 21
Views: 8047

So if you add an aftermarket wideband there is no way to datalog it through k-pro?? I'm confused. I'm looking at getting an Innovative Wideband because the factory o2 can't read below 11.5. That makes it very hard to tune my nitrous setup since I'm shooting for 11.5-11.7 A/F's. Is there any way to d...
by Bflaker
Fri Aug 29, 2008 5:17 am
Forum: K-Pro / KManager
Topic: Car Jerks when decelerating
Replies: 22
Views: 11220

has anyone found a solution to this? it gets real tiring when your in traffic. Solutions are: Overrun cutoff, TPS adjustment, and possibly igniton/fuel adjustment in columns 2 and 3. My car used to jerk when decelerating but now it is perfectly smooth after I making adjustments to the parameters an...
by Bflaker
Fri Aug 29, 2008 5:16 am
Forum: K-Pro / KManager
Topic: Nitrous outputs: Some general questions
Replies: 2
Views: 1955

I was curious about this too when I was installing my nitrous setup. Thanks for the clarification.