Search found 21 matches
- Thu Jun 02, 2011 10:18 am
- Forum: s300 / SManager
- Topic: Lean during wheelspin?
- Replies: 3
- Views: 2268
Re: Lean during wheelspin?
Thats what I was thinking but wanted to confirm. Thanks. Still curious though is it normal to see a little leaner A/F when wheel spinning. Its not going extremely lean; for example if the wheels aren't spinning and are under load 11.4 AFR when they start to spin 13.5 AFR.
- Thu Jun 02, 2011 8:11 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1791825
Re: SManager software requests
It would be nice to have the ablity to turn the fuel pump relay on and off with key-on engine-off. More than once I wanted to drain my fuel and had to rig a battery to the pumps.
Also the ablity to reivew if lean protection kicked in in the sensors window (similar to the way you have BstC displayed)
Also the ablity to reivew if lean protection kicked in in the sensors window (similar to the way you have BstC displayed)
- Thu Jun 02, 2011 7:56 am
- Forum: s300 / SManager
- Topic: Lean during wheelspin?
- Replies: 3
- Views: 2268
Lean during wheelspin?
I noticed on my datalogs whenever I get a moderate amount of wheelspin my A/F goes leaner. This is causing me to hit lean cut which is annoying. I understand my lean cut is on the aggressive side. Lean 1 never triggers Lean 2 is the issue my Lean 2 settings are below: Max A/F: 11.8:1 Load: 14.1 psi ...
- Wed Jun 10, 2009 10:56 am
- Forum: s300 / SManager
- Topic: NO START AFTER WARM UP
- Replies: 2
- Views: 2100
- Wed Jun 10, 2009 10:22 am
- Forum: s300 / SManager
- Topic: Anti-Lag building very little boost
- Replies: 9
- Views: 6508
- Tue Jun 09, 2009 10:47 am
- Forum: s300 / SManager
- Topic: Anti-Lag building very little boost
- Replies: 9
- Views: 6508
- Tue Jun 09, 2009 7:58 am
- Forum: s300 / SManager
- Topic: Anti-Lag building very little boost
- Replies: 9
- Views: 6508
post a datalog. raise your limiter to 6000, and change fuel to 400. Did you make sure to put a -40 and not 40 in the timing field? Yes I confirmed that I put -40 timing. I will try your suggestions today and hopefully post a log. Is the Fuel value an actual percentage of fuel enrichment or is it si...
- Mon Jun 08, 2009 3:51 pm
- Forum: s300 / SManager
- Topic: Anti-Lag building very little boost
- Replies: 9
- Views: 6508
Anti-Lag building very little boost
Frist off I'd like to say that I have searched this issue at length and have tried various fuel and timing retard combinations. For some reason I am only able to make 1.5psi with anti-lag I have tried settings up to: 350% fuel enrichment -40 deg of timing My launch rev limiter is 4000 rpm and fuel a...
- Wed Mar 18, 2009 2:05 pm
- Forum: s300 / SManager
- Topic: Set ignition timing option
- Replies: 10
- Views: 15339
Set ignition timing option
When using the set ignition timing option in SManager do you still have to jump the service connector like it shows in the service manual?
- Fri May 30, 2008 10:09 am
- Forum: Romeditor 4 Software
- Topic: Trouble With AEM UEGO
- Replies: 2
- Views: 20551
I seem to have gotten my AEM UEGO to work better now. FYI for those of you running one of these gauges. What I noticed is when I riched the car up to the gauge's max reading of 10.0:1 afr the output from the white wire (analog) read 1.54 volts instead of what the AEM manual said (0.00). Below are my...
- Thu May 29, 2008 11:23 am
- Forum: Romeditor 4 Software
- Topic: Trouble With AEM UEGO
- Replies: 2
- Views: 20551
Trouble With AEM UEGO
I've been searching around this forum and found that the best place to take the power for a wideband is from the fuse panel. My question is: Why not take it off the ECU power and ground from the 'A' connector. This is what I did but I fear that its messing with my wideband readings. It seems the ric...
- Sun May 25, 2008 2:12 pm
- Forum: Romeditor 4 Software
- Topic: Hondata Romulator with RomEditor Cable
- Replies: 1
- Views: 14723
Hondata Romulator with RomEditor Cable
Just wondering if and how I can use my RomEditor 4 usb-serial cable with the transonics rom emulator. Is it possible?
- Thu Nov 29, 2007 5:52 pm
- Forum: Romeditor 4 Software
- Topic: 64 bit support
- Replies: 7
- Views: 10365
- Sun Nov 25, 2007 10:40 am
- Forum: Romeditor 4 Software
- Topic: 64 bit support
- Replies: 7
- Views: 10365
- Wed Nov 21, 2007 12:53 am
- Forum: Romeditor 4 Software
- Topic: 64 bit support
- Replies: 7
- Views: 10365