Sorry, I gave up on this a LONG time ago!Dervi wrote:I am an O2 user. Also i want to know about it. Please give me a solution about it. If you tell me a good suggestion then it will be very helpful to me. I am waiting for the suggestion from all of you.
Search found 128 matches
- Tue Apr 03, 2012 11:37 pm
- Forum: K-Pro / KManager
- Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
- Replies: 17
- Views: 16481
Re: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
- Thu Aug 11, 2011 11:38 am
- Forum: K-Pro / KManager
- Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
- Replies: 5
- Views: 3113
Re: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
Are none of the wires required for the ECU to make the engine run? I don't want to cut wires that will be needed.Spunkster wrote:It is completely up to you which input you use. ANy input used you will have to cut the wire that goes to the original component for it to work.
- Sun Jul 31, 2011 10:56 am
- Forum: K-Pro / KManager
- Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
- Replies: 5
- Views: 3113
Re: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
This I know, I just need to know which ECU wire is best to use to wire the one I'm going to fit to.retroid wrote:we don't have clutch switch mate (EUDM) but you may install one.
- Sat Jul 30, 2011 1:55 am
- Forum: K-Pro / KManager
- Topic: EP3 JRSC High idle when cold
- Replies: 2
- Views: 1791
Re: EP3 JRSC High idle when cold
All the closed loop fuel trims are positive - this tells us that the fuel tables are too lean. Thank for your reply :-) Any suggestions what I should do to sort this? I am planning to fine tune the calibration by moving my wideband O2 sensor to the front of the CAT and forcing Open Loop. What is th...
- Fri Jul 29, 2011 1:39 am
- Forum: K-Pro / KManager
- Topic: EP3 JRSC High idle when cold
- Replies: 2
- Views: 1791
EP3 JRSC High idle when cold
- can't remember serial number, but under 4111 - KManager version 1.5.1.0 - the calibration is attached - a datalog of a problem is attached - Euro EP3 Civic Type-R - PRA Hondata K-Pro - Gruppe-M air intake, JRSC (650 injectors, 3.4 inch pulley, 9psi), Hondata manifold gasket, Mugen header with CAT,...
- Thu Jul 28, 2011 11:33 am
- Forum: K-Pro / KManager
- Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
- Replies: 5
- Views: 3113
Re: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
Does my ECU not require or use any of these inputs for anything else? I don't mind cutting a wire if it isn't required.Spunkster wrote:It is completely up to you which input you use. ANy input used you will have to cut the wire that goes to the original component for it to work.
- Thu Jul 28, 2011 6:07 am
- Forum: K-Pro / KManager
- Topic: EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
- Replies: 5
- Views: 3113
EP3 with PRA ECU, which pin to use for CLUTCH SWITCH?
I have a UK EP3 with PRA ECU. I fancy trying the clutch switch for full throttle shifting and was wondering which pin on the ECU is best to use: E16, E22, E29 or B9. My Civic has air con and still has power steering if this makes any difference. Are any of these pins normally used by the ECU or can ...
- Fri Jul 03, 2009 11:11 am
- Forum: K-Pro / KManager
- Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
- Replies: 17
- Views: 16481
- Sat Jun 20, 2009 2:38 pm
- Forum: K-Pro / KManager
- Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
- Replies: 17
- Views: 16481
No i didn't cut the cables. Just did a proper soldering job on the side of the cables about 3cm away from the conector and isolated them with tape. Will take picture for you. I also used conectors to make it more practical in case i youd need to unplug it or use another WB in my car. You'll see it ...
- Thu Jun 18, 2009 2:02 pm
- Forum: K-Pro / KManager
- Topic: Euro PRA w/ oem RSX O2 wideband in ELD pin possible ????
- Replies: 17
- Views: 16481
I have Innovate Motorsports LC-1 hooked up to my PRA KPRO ECU. I'm using it for WB and NB too. Wiring is as follows (6 wires LC-1 version): ECU conector A: A6 [PHO2S+] - Yellow wire (Narrowband O2 output) A5 [PG1] - Blue wire , Black Wire , Metalic/White wire (Ground - thick black cable) ECU conect...
- Thu Jun 11, 2009 2:32 pm
- Forum: K-Pro / KManager
- Topic: Innovate LC-1 on Euro CTR with PRA K-Pro
- Replies: 5
- Views: 4911
You might get a voltage offset when you connect the wideband output to the ELD pin. If so, program the LC-1 to flatline set voltages to calibrate the expected output voltages to the actual voltage the ECU reads. My conversion table looks like this: Actual LC-1 voltage---o2 sensor voltage---AF Ratio ...
- Mon Mar 30, 2009 2:33 pm
- Forum: K-Pro / KManager
- Topic: Can I copy calibration tables from different ECU type?
- Replies: 7
- Views: 6394
- Sun Mar 29, 2009 2:52 pm
- Forum: K-Pro / KManager
- Topic: KManager 1.3.5.4
- Replies: 25
- Views: 16710
Whenever I download the update using the link in this thread my AVG scanner throws up a virus warning stating there is a virus with the new .exe file. The virus is Win32/Virut.Z Anyone else get this? I have AVG but recently reinstalled with the latest download. I think I did get the same warning be...
- Sun Mar 29, 2009 2:43 pm
- Forum: K-Pro / KManager
- Topic: Can I copy calibration tables from different ECU type?
- Replies: 7
- Views: 6394
- Sat Mar 28, 2009 2:50 pm
- Forum: K-Pro / KManager
- Topic: is there a way to make a sound for shifting
- Replies: 9
- Views: 4104