Search found 10 matches
- Mon Jul 05, 2010 8:21 pm
- Forum: s300 / SManager
- Topic: New to Hondata: car running hot
- Replies: 5
- Views: 3053
Are you sure this datalog and calibration go together? You have the FANC override activated at 180 degrees with a max VSS of 120 MPH but at around frame 7:49 your ECT is 199 and VSS is 63 MPH but FANC is OFF. The FANC finally comes on when you dip to 30MPH at 9:31. Also, how was your block sleeved? ...
- Mon Jul 05, 2010 7:59 pm
- Forum: s300 / SManager
- Topic: Too much timing in map to cause heat problems?
- Replies: 8
- Views: 4532
What engine is this? A JRSC on what? I looked at your calibration and data log and I have a couple of comments. 1 - This probably doesn't have anything to do with your over heating problem but take a look at your Fuel Compensation settings. It looks like you have the stock settings for air temp comp...
- Sat Feb 06, 2010 9:17 pm
- Forum: Non-Hondata
- Topic: Hondata heatshield race gasket
- Replies: 1
- Views: 2528
Hondata heatshield race gasket
Is the "race" version of the heatshield IM gasket still available?
- Mon Aug 04, 2008 9:19 am
- Forum: s300 / SManager
- Topic: SMANAGER REQUEST:
- Replies: 2
- Views: 1781
In addition...
X2
plus...
The ability to select the area of the graph that is used to calculate these figures.
plus...
The ability to select the area of the graph that is used to calculate these figures.
- Mon Aug 04, 2008 9:09 am
- Forum: s300 / SManager
- Topic: SManager V.1.3.7
- Replies: 13
- Views: 8563
The download link points to v1.3.8
When I download from the link the installer file is named SManagerV1-3-8.exe. Has this actually been released yet? I see the digital signature on it is dated 8/1/08.revlinemotors wrote:When you update, it says updating/installing 1.3.6 :)
- Mon May 12, 2008 8:20 pm
- Forum: s300 / SManager
- Topic: plx sm-afr voltage offset
- Replies: 3
- Views: 2345
- Mon May 12, 2008 8:15 pm
- Forum: s300 / SManager
- Topic: S300 with PLX error code D10 ELD
- Replies: 4
- Views: 3792
- Mon May 12, 2008 8:08 pm
- Forum: s300 / SManager
- Topic: Setting D16Y8 timing
- Replies: 3
- Views: 3620
Thanks Spunkster, but I've already read the help and I know how to run the command. Let me try to re-phrase my question. When you invoke the set timing form it comes up set at 16 degrees. Since the base timing of the D16Y8 is normally at 12 degrees, do I change the set timing form to 12 and leave th...
- Fri May 09, 2008 10:23 pm
- Forum: s300 / SManager
- Topic: Setting D16Y8 timing
- Replies: 3
- Views: 3620
Setting D16Y8 timing
I'm using the P28 calibration as a starting point for tuning my D16Y8. How do you recommend setting the base timing? The base timing for a Y8 is 12 degrees. Do I adjust the dizzy to match 12 or 16 degrees? Are any adjustments to the timing map needed? BTW - After downloading the latest version that ...
- Sun Mar 23, 2008 7:56 am
- Forum: s300 / SManager
- Topic: S300 dies
- Replies: 1
- Views: 1454
S300 dies
My S300 flips on and off after a few minutes. I just installed a P28 w/S300 to run my D16Y8. There were no issues running the Y8 when using the stock P2P ECU. The ignition system is stock and the only aftermarket mod is an air intake. I began by running a P28 base map. I am able to datalog with my l...