Search found 53 matches

by megomaniac
Tue Apr 16, 2013 9:20 am
Forum: S300 Calibrations
Topic: ID1000cc Injectors H22a Turbo
Replies: 1
Views: 2526

Re: ID1000cc Injectors H22a Turbo

here's my map, its a rough tune, only low load got tuned before I had other issues on the dyno.
t3/67mm turbo
id1000 injectors
omni 4bar map
ge intake manifold
70mm tb
base fuel around 50psi
by megomaniac
Wed Jul 11, 2012 8:59 pm
Forum: S300 Calibrations
Topic: H22 turbo passed emisssions
Replies: 1
Views: 2683

Re: H22 turbo passed emisssions

updated, rebuilt and running again...
by megomaniac
Thu Jun 16, 2011 7:41 pm
Forum: s300 / SManager
Topic: H22a VTEC Spooling Issue
Replies: 1
Views: 1805

Re: H22a VTEC Spooling Issue

post your calibration,

fuel reg. vac line?
by megomaniac
Thu Jun 16, 2011 9:07 am
Forum: Coil Pack Retrofit
Topic: Coil Pack Retrofit
Replies: 88
Views: 349147

Re: Coil Pack Retrofit

would it be possible to elimate distributor on a h22,
using obd2 oil pump/crank sensor
but you still need the cylinder postions sensor in dizzy?
by megomaniac
Thu Jun 16, 2011 8:40 am
Forum: S300 Calibrations
Topic: H22 turbo passed emisssions
Replies: 1
Views: 2683

H22 turbo passed emisssions

walbro 255 id1000 .82ar 67mm t3 3inch down, ceramiac high flow no name cat, vibrant ultra quiet resonator, big magnaflow muffler synapse turbo h22 manifold, heat wrapped mani, down, and wrapped the cat too. no egr, purge, iacv, fitv. golden eagle im shell 91 fresh oil cut it really close, Nox limit ...
by megomaniac
Mon Jun 13, 2011 4:07 pm
Forum: S300 Calibrations
Topic: Piston change - Need help adjusting my turbo basemap
Replies: 8
Views: 5982

Re: Piston change - Need help adjusting my turbo basemap

when you go to make changes to your fuel tables, be sure you are looking at the fuel table and not the timing map. there is a high speed timing, low speed timing high speed fuel , low speed fuel the difference bewteen high and low speed map is vtec in vtec is high not in vtec is low just wanted to m...
by megomaniac
Mon Jun 13, 2011 3:57 pm
Forum: S300 Calibrations
Topic: Piston change - Need help adjusting my turbo basemap
Replies: 8
Views: 5982

Re: Piston change - Need help adjusting my turbo basemap

is there anything i can do for the idle? do you just adjust the cells that it sits on when idling, and keep reducing fuel until it idles at 14.7? thanks :) thats exactly what i do, just be sure its at operating temp, i like to set up the coolant temp compensations, and air intake compensations in t...
by megomaniac
Mon Jun 13, 2011 11:51 am
Forum: S300 Calibrations
Topic: Launch control "popcorn" ?
Replies: 3
Views: 11814

Re: Launch control "popcorn" ?

I haven't done it but, I have read that it is from adjusting the values so it's rich and timing retarded. so when charge ignites, it flames out of the combustion chamber, to help spool big turbo. this can be potentially dangerous cause of the increase in exhaust gas temp in exhaust ports, manifold, ...
by megomaniac
Mon Jun 13, 2011 11:30 am
Forum: S300 Calibrations
Topic: Piston change - Need help adjusting my turbo basemap
Replies: 8
Views: 5982

Re: Piston change - Need help adjusting my turbo basemap

http://i1121.photobucket.com/albums/l504/megomaniac1/Untitled.jpg -table showing is fuel value table for low speed map, this is the table you need to adjust to add or remove fuel. -you can also view recorded lambda values, upside down "Y" symbol what i do is select the the cells i want to...
by megomaniac
Sun Jun 12, 2011 9:17 pm
Forum: S300 Calibrations
Topic: Piston change - Need help adjusting my turbo basemap
Replies: 8
Views: 5982

Re: Piston change - Need help adjusting my turbo basemap

If you can, wire up the 5v from your wideband to datalog with ecu. use the offset voltage to get reading to match your gauge if you need to. then you can review your data logs, and make adjustments as nessary. what I do is look at the estimated %change table, and recorded a/f table, and just tweak i...
by megomaniac
Sat Jun 11, 2011 9:29 am
Forum: S300 Calibrations
Topic: Piston change - Need help adjusting my turbo basemap
Replies: 8
Views: 5982

Re: Piston change - Need help adjusting my turbo basemap

rent a trailer. Closed loop doesn't work well, until the open loop maps are close to tagert a/f ratio. you need to run your car in open loop, watching your wide band, set your idle and adjust the map + or - to get to 14.7 a/f. keep an eye on display as well, cause the coolant compensations are going...
by megomaniac
Wed May 25, 2011 5:38 pm
Forum: S300 Calibrations
Topic: H22A 15 psi 1000cc injectors
Replies: 24
Views: 62878

Re: H22A 15 psi 1000cc injectors

maybe if you post a bigger picture, you'll get more replys...Image
by megomaniac
Wed Nov 03, 2010 6:11 pm
Forum: s300 / SManager
Topic: Program to change RPM and Load indexes from S300 calibration
Replies: 16
Views: 10444

is this safe to download? I'm in a hotel and it said the proxy server can't download or something?
by megomaniac
Sat Sep 25, 2010 10:09 am
Forum: s300 / SManager
Topic: 1998 prelude SH with S300
Replies: 3
Views: 2980

hondata is obd1,

might need to change to obd1 distributor, cause the crank position sensor might not work,
by megomaniac
Sat Aug 14, 2010 10:41 am
Forum: S300 Calibrations
Topic: h22 turbo map work in progress
Replies: 2
Views: 2810

I won't get a chance to drive it for a while, out of province working. I think I have some other things to figure out before more tuning. need to confirm what map sensor I have, It's a onmi, but could be anything from a 2.5 to a 4, not 100% sure, I think it might be a 3bar, came with the TB i bought...