Search found 14 matches
- Wed Jan 02, 2013 5:11 pm
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: lambda overlay not working?
- Replies: 2
- Views: 2968
Re: lambda overlay not working?
ok thanks.
- Mon Dec 31, 2012 10:05 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: lambda overlay not working?
- Replies: 2
- Views: 2968
lambda overlay not working?
I dont think the Lambda overlay is working with the 2012+ units? It works fine same software 1.4.3.0 with the 8th gen calibrations. but the 9th gen calibrations will not show lambda overlay. anyone else seen this issue?
- Thu Apr 15, 2010 7:53 pm
- Forum: s300 / SManager
- Topic: Anyone else with PWM boost control randomly not working?
- Replies: 31
- Views: 18988
Ok so I tested just the software update first. First passes the car made boost in each gear no problem.. then the second pass it stage at gate pressure. about 7 psi.. So after that i added the Diode. drove the car down to the lanes an it boosted up in 1st and second properly.. But then that run down...
- Mon Apr 12, 2010 2:12 pm
- Forum: s300 / SManager
- Topic: Anyone else with PWM boost control randomly not working?
- Replies: 31
- Views: 18988
This is pretty interesting. I will try this out.. It may explain why I have not seen this issue on my other systems.. I generally setup non s300 ecus with A17 +12out from the ecu to control my PWM solenoids. The A17 circuit must handle the noise differently. I will test and let you know. thanks for ...
- Mon Apr 12, 2010 10:14 am
- Forum: s300 / SManager
- Topic: Anyone else with PWM boost control randomly not working?
- Replies: 31
- Views: 18988
He is a log from the track. Gate spring is a 7 psi spring.. the car never boosted over the gate level. but the PWM is showing it trying to target higher.. the next pass was fine no changes to the calibration or car.. I have 2 cars with this issue if there is anything that could be tested i am willin...
- Fri Apr 09, 2010 9:38 am
- Forum: FlashPro Manager
- Topic: Possible addition to Flashpro?
- Replies: 2
- Views: 2324
Possible addition to Flashpro?
Would it be possible to use the serial input of a wideband to log in flashpro? It would save temporarily wiring the analog signal into the car?
- Fri Apr 09, 2010 9:14 am
- Forum: s300 / SManager
- Topic: Anyone else with PWM boost control randomly not working?
- Replies: 31
- Views: 18988
- Mon Apr 05, 2010 9:41 am
- Forum: s300 / SManager
- Topic: where to connect an AEM wide band 2 a Hondata P28 .
- Replies: 5
- Views: 3287
- Mon Apr 05, 2010 8:55 am
- Forum: s300 / SManager
- Topic: where to connect an AEM wide band 2 a Hondata P28 .
- Replies: 5
- Views: 3287
- Tue Oct 13, 2009 9:41 am
- Forum: s300 / SManager
- Topic: SManager V1.4.3 beta
- Replies: 8
- Views: 6033
Re: SManager V1.4.3 beta
Download here · Added maximum speed for radiator fan override. This allows you to switch the radiator fan off at a certain vehicle speed. Normally by 30-40 mph the radiator fans stalls, so is not contributing to the airflow over the radiator. · Added boost control solenoid frequency. By default the...
- Tue Jun 30, 2009 2:00 pm
- Forum: K-Pro / KManager
- Topic: ECT Timing and Fuel Adjustments
- Replies: 1
- Views: 1269
- Mon Jun 29, 2009 10:51 am
- Forum: K-Pro / KManager
- Topic: ECT Timing and Fuel Adjustments
- Replies: 1
- Views: 1269
ECT Timing and Fuel Adjustments
Will there be ECT fuel and timing adjustments made available in KPRO? If adjustments are not available do we know what timing and fuel modifications the stock Honda code is making at the different temps?
- Wed May 06, 2009 4:53 pm
- Forum: s300 / SManager
- Topic: cant go into closed loop?
- Replies: 29
- Views: 13635
- Wed May 06, 2009 8:59 am
- Forum: s300 / SManager
- Topic: cant go into closed loop?
- Replies: 29
- Views: 13635
Re: cant go into closed loop?
ok i just got all my obd1 swap done and was datalogging but my short and long term fuel trims where at zero. I have the my PLX wired into D10 eld. but if closed loop is checked or unchecked nothing changes or even if i change my short trim adjustments still zero. am i not going into closed loop? th...