Search found 18 matches

by Mura
Fri Jul 27, 2007 6:47 am
Forum: K-Pro / KManager
Topic: Need advice with Toda A3 cams
Replies: 1
Views: 1533

Need advice with Toda A3 cams

This is the story below about our unsuccesful installation of A3 cams to EP3. It was our second experience with A3 cams, first time we had not any problems. Have been set up at one time: A3 cams Toda springs Toda tensioner ECU - Hondata K-Pro Right now after start the engine we've found that idle is...
by Mura
Tue Feb 27, 2007 9:03 am
Forum: s300 / SManager
Topic: High Impedence or Low Impedence injectors?
Replies: 7
Views: 3034

Re: High Impedence or Low Impedence injectors?

Which ones does Hondata recommend? In theory low impedence injectors will open faster when using bigger injectors, thus giving better control at idle and low durations. I am using a resistor box right now, just because the car had one to start with although I can run without it if I have the proper...
by Mura
Thu Jan 18, 2007 10:25 am
Forum: K-Pro / KManager
Topic: Need advice from Hondata or installers
Replies: 2
Views: 1620

Need advice from Hondata or installers

We've got PRC ECU of customer, but we are not sure about condition of ECU, it was taken from damaged car and there was no possibility to test it before installation. I've set up K-Pro and tried to ERASE. Erasing is OK. Try to UPLOAD after. Uploading went but TOO FAST, maybe couple of seconds. MIL li...
by Mura
Wed Dec 14, 2005 3:10 am
Forum: s300 / SManager
Topic: S300 into P72 JDM
Replies: 8
Views: 5119

Where are you from?

we have an experience of setting-up of S300 to JDM's ECu.

We could send you the pictures.
by Mura
Tue Dec 06, 2005 5:09 am
Forum: s300 / SManager
Topic: S300 & JDM P30
Replies: 5
Views: 3065

Yes, we've made it

you can make something like podium with few sockets. It's looks like podium using on S200 with Romulator. You should insert 2 male sockets to the upper level of this podium. Also you should solder 4-pin socket by wires. Sure, you could not to close the cover of ECU after this installation, but I thi...
by Mura
Tue Nov 15, 2005 11:55 am
Forum: Applications
Topic: Auto tranny application
Replies: 1
Views: 1374

Auto tranny application

I know that Hondata does not work with AT. But some guys here was tried with success to link on AT vehicles two ECUs. Unfortunayely only on Toyotas for a while. One ECU for AT operation One ECU for engine All of power supply, grounds and inputs are made parallel for both ECUs. Sure outputs are going...
by Mura
Tue Oct 18, 2005 5:47 am
Forum: s300 / SManager
Topic: Greddy Profec B high boost activation
Replies: 5
Views: 3048

2 RMS

I've tried to find something, but no result.

Am I right that you could make device like this?

If it's possible please send me email with pricing.

PS Can not understand how to send PM on this forum , sorry )))
by Mura
Wed Oct 12, 2005 6:41 am
Forum: s300 / SManager
Topic: Greddy Profec B high boost activation
Replies: 5
Views: 3048

Greddy Profec B high boost activation

I'd like to make auto activation of high boost on Greddy profec. I have got remote button already and push it on 3 gear for high boost. If I understand right I should send one SHORT pulse to the wire connected on the rear side of controller. Which device could I use for this pulse oscillation? All o...
by Mura
Fri Jul 01, 2005 6:59 am
Forum: s100/s200
Topic: Cuttoff of injectors ??
Replies: 14
Views: 6144

Voltage

of TPS is 0.47-0.49 (0-1 degree).

I will try to post datalog shortly.
by Mura
Wed Jun 29, 2005 6:57 am
Forum: s100/s200
Topic: Cuttoff of injectors ??
Replies: 14
Views: 6144

Cuttoff of injectors ??

During driving on low TPS angles like 2-3 degree sometimes injectors cuttoffs are occuring. It's very annoing stuff.

What is it possible to do?

P.S. TPS is zero when throttle is closed.
by Mura
Mon Mar 21, 2005 3:37 am
Forum: s100/s200
Topic: nitrous control help?
Replies: 8
Views: 2826

2 RMS

Where can I read more about your ECUs and daughter plate for nitrous purposes?
by Mura
Mon Mar 21, 2005 2:53 am
Forum: s100/s200
Topic: JDM GSR throttle body
Replies: 1
Views: 1233

JDM GSR throttle body

we've set up S200 with JRSC to JDM integra. It has not FAST IDLE valve at all, I don't know why. Because of that we have big problem during cold start.
With stock JDM ECU there are not any problem with cold start.
Now we have USDM P72 ECU and have this problem.

Any ideas about this issue?
by Mura
Thu Oct 28, 2004 6:43 am
Forum: s100/s200
Topic: No power gain after 6000?
Replies: 2
Views: 1434

We have

in Moscow 92, 95 and 98 octane fuel here. I'm driving on 98. Yes, 30" at WOT, but I'd like to check my start ignition because Hondalogger shows 14" and I set 16" in Romeditor. If my start ignition is 14", I think I have just 28" at WOT. Am I right? Is it possible to set up the distributor using only...
by Mura
Thu Oct 21, 2004 9:58 am
Forum: s100/s200
Topic: No power gain after 6000?
Replies: 2
Views: 1434

No power gain after 6000?

What should be the reason of that? After 6000 to 7500 power curve looks like horizontal with strange spikes.
Fueling is 12.5
Belt is OK.
Ignition in WOT near 30.

JRSC 7 lbs H22 Prelude
by Mura
Thu Oct 21, 2004 9:51 am
Forum: s100/s200
Topic: h22a map
Replies: 5
Views: 3043

Chuvak, chto ty

purgu to gonish, napraslinu navodish? Stendov blya jopoi esh, da i stend dlya nastroiki vovse neobyazatelen. Dam ya tebe kartu, tolko hah ona tebe neotstoennaya? Prochitai sperva, o chem sait, potom karty prosi. Prablemy u nego....
:evil: :evil: :evil: