Search found 32 matches

by sicones
Tue Dec 09, 2014 5:11 am
Forum: s300 / SManager
Topic: fuel pressure datalog
Replies: 8
Views: 3374

Re: fuel pressure datalog

So your saying it does not seem normal? I tried a completely different s300/p28 combo and I get the same choppy datalogging results. I fail to believe this brand new AEM sensor is faulty and 2 different 255 pumps, FPR and filter do the same thing. The overall wiring in the car, engine harness, fuel ...
by sicones
Sun Nov 30, 2014 9:59 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 107702

Re: SManager software requests

^this and when are we getting closed loop boost control?
by sicones
Fri Nov 28, 2014 9:55 am
Forum: s300 / SManager
Topic: ABS Sensor for wheel speed
Replies: 1
Views: 1268

Re: ABS Sensor for wheel speed

No the ABS sensors do not connect to the ECU/S300. You can install a a second rear wheel speed sensor and wire it into the factory VSS input to measure rear wheel speed, xenocron.com sells the sensor and kit.
by sicones
Mon Nov 17, 2014 4:27 pm
Forum: s300 / SManager
Topic: fuel pressure datalog
Replies: 8
Views: 3374

Re: fuel pressure datalog

Sensor is mounted directly to the fuel rail.
by sicones
Mon Nov 17, 2014 2:40 pm
Forum: s300 / SManager
Topic: fuel pressure datalog
Replies: 8
Views: 3374

Re: fuel pressure datalog

and yes I removed R2 and R3, at some point I was using this input for the innovate WB, which is now on D12.
by sicones
Mon Nov 17, 2014 11:41 am
Forum: s300 / SManager
Topic: fuel pressure datalog
Replies: 8
Views: 3374

Re: fuel pressure datalog

I posted the .ini for settings, are you able to view it? Its a linear sensor so I added more data points then necessary. I entered the values found on the datasheet that came with the sensor. I'm not at my computer now but I think its 0.5v = 0psi and 4.5v = 100psi
by sicones
Sun Nov 16, 2014 3:17 pm
Forum: s300 / SManager
Topic: fuel pressure datalog
Replies: 8
Views: 3374

fuel pressure datalog

I installed an AEM 100psi fuel pressure sensor on analog input 2 (B6). Is it normal for a walbro 255 to fluctuate this much in boost or is this a problem with the sensor/datalogging. I'm using an old S300 V1. Car is a 98 civic, turbo D16y8, ID1000, GT3071R. I already swapped pumps, fuel filer and FP...
by sicones
Wed Jan 16, 2013 3:41 pm
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

That was it, thanks.
by sicones
Sun Jan 13, 2013 6:22 am
Forum: s300 / SManager
Topic: Does Anybody Think this Tune is complete? Fuel table pics.
Replies: 7
Views: 4816

Re: Does Anybody Think this Tune is complete? Fuel table pic

You should be making over 200whp even on 5lbs, unless its some really tiny turbo. I've tuned naturally aspirated b series with low compression to over 180 whp. These were motors built for turbo with no turbo. Your powerband should keep climbing all the way to redline, something doesn't add up.
by sicones
Sat Jan 12, 2013 11:38 am
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

Still doesn't work, I've tried every possible scenario except another laptop which should not matter. Even XP mode on my Win7 computer. Opened a brand new calibration and uploaded didn't work either. Also, that bug is still there under secondary tables parameter, the Nitrous Active check boxes don't...
by sicones
Fri Jan 11, 2013 6:44 pm
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

How do I know it doesn't work? Cooling fan doesn't come, fuel pump doesn't run (walbro is loud as hell), nitrous solenoid and relay no clicky, no click from AC clutch.
by sicones
Fri Jan 11, 2013 6:36 pm
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

I plug in the laptop, put key in II, upload calibration, start datalogging, when I go to the test outputs window checking any of the boxes does nothing.
by sicones
Thu Jan 10, 2013 7:46 pm
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

I just tried it with v2.2.4, still doesn't work. I also did an Erase ECU command and re-uploaded, didn't help. I'm not to concerned with this feature but it would be nice, ecm link has had this for a while.
by sicones
Thu Jan 10, 2013 5:02 pm
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

I tried all of them, but I really want to test A10 for my nitrous solenoid.
by sicones
Thu Jan 10, 2013 3:42 pm
Forum: s300 / SManager
Topic: test outputs
Replies: 13
Views: 3391

Re: test outputs

Of course, just uploaded the new calibration after the update. Cycled the key to clear the CEL that usually happens after an update. I tried it with datalogging on and datalogging off. It doesn't work.