Search found 15 matches

by Muu
Mon Jun 17, 2013 11:56 am
Forum: Traction Control with KPro
Topic: PRA & K100 supports TC?
Replies: 2
Views: 9982

Re: PRA & K100 supports TC?

OK great but fine if dealer is setting up.
by Muu
Sun Jun 16, 2013 3:00 pm
Forum: Traction Control with KPro
Topic: PRA & K100 supports TC?
Replies: 2
Views: 9982

PRA & K100 supports TC?

As per title really, does the PRA euro ECU and K100 support the TC module?
by Muu
Thu Jan 05, 2012 10:26 am
Forum: K-Pro / KManager
Topic: IT LIVES! - Lotus K20 swap...
Replies: 0
Views: 1338

IT LIVES! - Lotus K20 swap...

Started first time and idles super smooth, just need to clean up the wiring and put undertray back on for a test drive. http://farm6.static.flickr.com/5210/5234632757_2f58a268f9_z.jpg Oh and I have OBD2 bluetooth to android to check on faults and parameters! https://p.twimg.com/AiaUFntCQAEODij.jpg
by Muu
Wed Jan 04, 2012 3:25 pm
Forum: K-Pro / KManager
Topic: C101 Pin 17 - RED/WHT - Any ideas?
Replies: 5
Views: 2251

Re: C101 Pin 17 - RED/WHT - Any ideas?

Yellow is multiplex but on the E8 plug, the C101 is all the chassis to engine connections.

Ok from reading a tracing the loom, C101/17 looks to be ECT feed for the dash (it loops off the C101 up to the E, hence two cables)

Pin 2 Yellow, is the 12v feed for the back up switch.

(long day!)
by Muu
Tue Jan 03, 2012 5:18 pm
Forum: K-Pro / KManager
Topic: C101 Pin 17 - RED/WHT - Any ideas?
Replies: 5
Views: 2251

Re: C101 Pin 17 - RED/WHT - Any ideas?

C101 is on the dash loom with the E plug, and hooks into the engine loom along side the A&B plug.

Also wondering what pin 2 (yellow) does too!
by Muu
Tue Jan 03, 2012 12:01 pm
Forum: K-Pro / KManager
Topic: Feed to E8 required?
Replies: 1
Views: 884

Feed to E8 required?

Hi

The lotus O2 relay is hardwired to the main relay (in one unit) so it just comes on with the main relay.

Question is, does E8 need to see a 12v signal to not think there is an issue with a dead relay?

T
by Muu
Mon Jan 02, 2012 5:20 pm
Forum: K-Pro / KManager
Topic: C101 Pin 17 - RED/WHT - Any ideas?
Replies: 5
Views: 2251

C101 Pin 17 - RED/WHT - Any ideas?

Hi

Have searched, read docs, looked in Hondata FAQ and still can't figure out what pin 17 does on the C101.

It has two red/wht cables on the one pin, and FYI this is a UK spec (PRA) loom and ECU.

Any help much appreciated.

Tim
by Muu
Mon Dec 12, 2011 11:08 am
Forum: K-Pro / KManager
Topic: Clarity on wiring up E1, E7 & E8
Replies: 2
Views: 1262

Re: Clarity on wiring up E1, E7 & E8

Ok so I'm clear now, it was as I thought. It's the relay coil gnd, which means 12v will be going to it when the main relay is on but it's not being fed constant 12v.
by Muu
Sun Dec 11, 2011 2:31 pm
Forum: K-Pro / KManager
Topic: Clarity on wiring up E1, E7 & E8
Replies: 2
Views: 1262

Clarity on wiring up E1, E7 & E8

Hi Just building a swap loom up and I'm a little bamboozled by some of the info around the PGM-FI relay, I'm sure it's simple just want to be sure as the following warning is scary enough: Do not wire the main relay (E7) or fuel pump (E1) to 12V. This will damage the ECU. Both E1 and E7 are outputs ...
by Muu
Wed Nov 02, 2011 1:08 pm
Forum: K-Pro / KManager
Topic: Lotus Multiplexer on PRA ecu?
Replies: 4
Views: 1479

Re: Lotus Multiplexer on PRA ecu?

AH fair enough
by Muu
Mon Oct 31, 2011 7:33 am
Forum: K-Pro / KManager
Topic: Lotus Multiplexer on PRA ecu?
Replies: 4
Views: 1479

Re: Lotus Multiplexer on PRA ecu?

Ah shame, is that a limitation of the PRA ecu?

Would have thought the majority of swapped cars aren't fed elises as I am not aware of kits for them?
by Muu
Sun Oct 30, 2011 4:26 pm
Forum: K-Pro / KManager
Topic: Lotus Multiplexer on PRA ecu?
Replies: 4
Views: 1479

Lotus Multiplexer on PRA ecu?

Hi

Noticed in a later version of the software there is support for driving Lotus clocks via the multiplexer out. Any more info on this?

My car is a UK lotus elise, with a PRA ecu and loom. Swapping to later clocks with the higher rev counter and 3 shift lights could be a nice upgrade.

T
by Muu
Wed Feb 02, 2011 5:53 am
Forum: Applications
Topic: PRB ecu on Euro K20A2 & Loom
Replies: 1
Views: 1981

PRB ecu on Euro K20A2 & Loom

Hi It looks like I need to use a PRB ecu in order to drive an AIM dash over RS232, so have been reading up on the differences. I know I need to buy the PRB wideband sensor and some wiring changes as outlined in http://www.hondata.com/techk20-ctr-o2wiring.html However is that the limit of the changes...
by Muu
Fri Jan 21, 2011 4:14 pm
Forum: Applications
Topic: 37820-PRA-Exx
Replies: 2
Views: 2151

many thanks
by Muu
Fri Jan 21, 2011 3:39 pm
Forum: Applications
Topic: 37820-PRA-Exx
Replies: 2
Views: 2151

37820-PRA-Exx

Hi

With the K100 application, does it matter which numbers are on the end of the ECU code?

T