Search found 29 matches

by Praylewd powr
Sun Mar 25, 2007 12:16 pm
Forum: s300 / SManager
Topic: Error 21 vtec spool on P28 ECU
Replies: 16
Views: 8696

I have had the exact same issue arise after I got my p28 s300 ecu back from Hondata. I have troubleshooted all the other things possible and swapped out two other vtec solenoids.
by Praylewd powr
Sat Mar 24, 2007 7:56 pm
Forum: s300 / SManager
Topic: attn Hondata: ECU related issue with s300 socketing
Replies: 7
Views: 3650

attn Hondata: ECU related issue with s300 socketing

Hondata, I just received my p28 ecu back from you guys and have been having a new issue that was not present when I ran my s200 previously. I am now getting code 21 vtec spool and have been reading the current other thread about it. I sent my ecu and hondata socketed it for boost and installed the s...
by Praylewd powr
Mon Dec 11, 2006 10:08 pm
Forum: s300 / SManager
Topic: Error code when opening previously opened .bin file
Replies: 2
Views: 1507

Error code when opening previously opened .bin file

I recently downloaded the latest version of SManager and opened a .bin file from Romeditor from my s200 setup before. I opened the file correctly, selected the first 20 columns, etc....and started making a few changes. I then saved the file, it still saved it as a .bin file. But when I try to open t...
by Praylewd powr
Tue Aug 16, 2005 6:18 pm
Forum: s100/s200
Topic: Attn: hondata--need s200 repaired/shipping info
Replies: 2
Views: 1391

I was going to swap the ecu just in case, but it was not required. I swapped just the blue box and I have my friends ecu as a spare for now. I ran the car, it is fine. I then swapped back to my blue box today, and the problem is definately the box.

Duane.
by Praylewd powr
Mon Aug 15, 2005 7:23 pm
Forum: s100/s200
Topic: Attn: hondata--need s200 repaired/shipping info
Replies: 2
Views: 1391

Attn: hondata--need s200 repaired/shipping info

Hondata, I live in edmonton, alberta, canada. I have an s200 serial no:0656. I pulled the car in my garage after work, let it idle before shutting it off, and heard a click (same as when you turn the key to accessory). The cars idle stuttered, then a CEL came up. I turned the car off, back on, and s...
by Praylewd powr
Mon Jun 06, 2005 7:20 am
Forum: s100/s200
Topic: Attn: Hondata - s200/ECU problems, please reply ASAP
Replies: 5
Views: 2672

When I check the red wire, I get 2mV and that's it! I did not change anything to cause this, and that 2mV is right off the p72 board where the interface cable was socketed. There is no reason for the ECU to go bad or for the socket to be a bad connection cause like I say, it was fine before the cabl...
by Praylewd powr
Sun Jun 05, 2005 10:49 pm
Forum: s100/s200
Topic: Attn: Hondata - s200/ECU problems, please reply ASAP
Replies: 5
Views: 2672

Attn: Hondata - s200/ECU problems, please reply ASAP

I have a p72 OBD1 ECU running an H22a, with s200 blue box. I recently have had issues with the interface box cable (like everyone else has) and don't know for sure if my problem is the cable, the box, or my ECU. I don't have the engine in the car right now, but my fuel pump primes so I know part of ...
by Praylewd powr
Tue May 17, 2005 10:19 am
Forum: s100/s200
Topic: RomeditorV3 for hondata + ostrich
Replies: 7
Views: 3753

How do you set it up in RomEditor then if it doesn't recognize it as Ostrich? What is it set as in the emulator settings?

Duane
Canada
by Praylewd powr
Tue Mar 29, 2005 7:26 am
Forum: HondaLogger Software
Topic: Hondata group: please check my datalogging code for me?
Replies: 4
Views: 3610

Works now, thanks.

d
by Praylewd powr
Sat Mar 26, 2005 9:51 pm
Forum: HondaLogger Software
Topic: Hondata group: please check my datalogging code for me?
Replies: 4
Views: 3610

No it does not say enabled, but I have purchased the datalogging feature through Speedtech Racing Development in Calgary, Alberta, Canada. When I put in the code, it just says connection error....but I know I have good communication between the s200 and my laptop. The code for my s200 serial no: 006...
by Praylewd powr
Fri Mar 25, 2005 12:59 am
Forum: HondaLogger Software
Topic: Hondata group: please check my datalogging code for me?
Replies: 4
Views: 3610

Hondata group: please check my datalogging code for me?

I recently purchased my datalogging feature ($50 upgrade due to old s200) and I input the code and I get a connection error....no error codes, just connection error in a green flash also on the upper left side of the screen. I had issues with my palmpilot so I upgraded to a laptop with a keyspan USB...
by Praylewd powr
Sat Mar 19, 2005 10:52 pm
Forum: HondaLogger Software
Topic: Palm log software freezes up on brand new Palm tungsten T5
Replies: 6
Views: 4051

Palm log software freezes up on brand new Palm tungsten T5

Like I posted elsewhere, I just downloaded the palmlog software to my brand new Tungsten T5....and it just freezes up. I actually had purchased a tungsten E before and it opened up on it, but was told that I could not connect it to my s200 cause it just had a USB slave. Anyways, could you please rep...
by Praylewd powr
Sat Mar 19, 2005 10:48 pm
Forum: HondaLogger Software
Topic: Hondata People please L@@K
Replies: 9
Views: 4771

I just downloaded the palmlog software to my Palm Tungsten T5 and it just freezes up too. I already purchased a cable from PC cables.....so I really want to fix it.

Hondata---could you please look into why this is happening?

Duane
Edmonton, AB, Canada
by Praylewd powr
Fri Feb 13, 2004 9:13 am
Forum: s100/s200
Topic: Can you use the clutch switch with the MSD digital 6 plus?
Replies: 1
Views: 1368

Can you use the clutch switch with the MSD digital 6 plus?

I have a p72 ECU with s200 module. I am also running the MSD digital 6 plus with the wholeshot rev control. I have installed the hondata clutch switch correctly (installation manual) and it is non-functional. I want the switch for the full throttle shift feature. Is there a compatibility issue? Duan...