Search found 312 matches

by Johnny_9
Tue Jul 21, 2015 1:07 am
Forum: s300 / SManager
Topic: S300 Bluetooth plug in?
Replies: 3
Views: 1504

Re: S300 Bluetooth plug in?

What about Bluetooth UART?
by Johnny_9
Mon Jul 20, 2015 8:20 pm
Forum: s300 / SManager
Topic: uncorrect ETC.c compensation on high load
Replies: 26
Views: 7560

Re: uncorrect ETC.c compensation on high load

Just did a coldish start, with v2.4.4 & a Wideband; much better...

A/F much more controllable below 80C open loop

No longer goes wildly rich when you give it some throttle during the post start window (<30 secs after starting)

Thanks.
by Johnny_9
Mon Jul 20, 2015 10:35 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 107833

Re: SManager software requests

Would be nice to be able to copy the Fuel Table sensor overlay (AF, Estimated Change in Fuel) from Smanager into Excel, so the fuel can be adjusted in excel and pasted back into SManager. OR have SManager update the fuel table with the "estimated Change in fuel", instead of Manually adjusting fuel ....
by Johnny_9
Thu Jul 09, 2015 10:20 am
Forum: s300 / SManager
Topic: uncorrect ETC.c compensation on high load
Replies: 26
Views: 7560

ETC.c compensation on tip-in <80C

Noted. Just did another data-log. Below ECT 80C, the ECTc will "spike" over the ceiling of Fuel ECTc (high load), when the throttle is jabbed. Above ECT 80C, the ECTc will "stay in range" as set by Fuel ECTc (high load). I did this both for (a) within 30 seconds of start-up and (b) after 30 seconds ...
by Johnny_9
Wed Jul 08, 2015 4:55 pm
Forum: s300 / SManager
Topic: uncorrect ETC.c compensation on high load
Replies: 26
Views: 7560

Re:Incorrect ETC.c compensation on high load

Here is the datalog re-posted (03-150706-093024.s3d) - the calibration is posted above At 3.685s just as the car is started, I jab the throttle and ECTc(%) jumps to 13.3% In the calibration (attached) and screenshot (Parameters, Fuel Compensation,>Water Temp>Open Loop -High Load (95kpa) the maximum ...
by Johnny_9
Wed Jul 08, 2015 5:43 am
Forum: s300 / SManager
Topic: uncorrect ETC.c compensation on high load
Replies: 26
Views: 7560

Re: uncorrect ETC.c compensation on high load

ECT starts at 36C and ends at 78c
by Johnny_9
Mon Jul 06, 2015 5:50 am
Forum: s300 / SManager
Topic: uncorrect ETC.c compensation on high load
Replies: 26
Views: 7560

Incorrect ETC.c compensation on high load?

I seem to be getting the same issue. Attached is screenshot of the data-log/parameters window of a start-up at 36C ECTc is showing 13.3% at 3.680 secs into the datalog (@TPS at 10%, 2,510rpm) This 13.3% ECTc in the datalog, EXCEEDS the open loop ECTc at 20C/41C of 11.7%/8.6% in the parameters window...
by Johnny_9
Fri Jun 19, 2015 4:43 am
Forum: s300 / SManager
Topic: Knock Retard (Datalog Export)
Replies: 4
Views: 1554

Knock Retard (Datalog Export)

Hondata, is it possible to do a quick beta version so that the Knock Retard data is exported, when doing a CSV export of datalog. Presently it (Knock in the exported CSV) has been missing (for sometime) I wish to import the exported csv datalog into another program for more sophisticated analysis (I...
by Johnny_9
Thu Jun 11, 2015 11:53 pm
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 107833

S300 - Ignition IAT Compensation

http://www.hondata.com/forum/viewtopic.php?f=19&t=16486&p=70711#p70711 Posting this previous request under software requests. In addition:- - More Ign-IATc breakpoints/sites: the existing 5 Ign-IATc may not be enough, and more would be helpful in a situation when the car is tuned during the (hot) da...
by Johnny_9
Fri Jun 05, 2015 2:37 am
Forum: s300 / SManager
Topic: S300v2 ECU Resetting Itself
Replies: 2
Views: 1004

S300v2 ECU Resetting Itself

I was data-logging on-board (USB not connected) for 20+ minutes with P72 S300 V2. The internal memory was 50% used After downloading the data log, the data log, though viewable had lots of jagged lines on any sensor trace. Also the ECU would not accept an calibration upload. When I downloaded the ca...
by Johnny_9
Wed Jun 03, 2015 6:48 pm
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 107833

Re: SManager software requests

Be nice to have Ignition ECT/IAT compensation parameters in the datalogs and graphs
by Johnny_9
Fri May 22, 2015 12:26 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 107833

Data log filter

Can we have more user-defined filter functionality on datalogs: example - Filter out TPS lower than 2% - AF > 15.0:1, - MAP - ability to cut out part of the datalog - ability to min-max, average for sensor overlays - ability to show IACV duty cycle or IACV ground Pulse-Width Move the sensor overlay ...
by Johnny_9
Fri May 22, 2015 12:16 am
Forum: s300 / SManager
Topic: Hot start idle low
Replies: 8
Views: 2102

Re: Hot start idle low

Post start - step 4.
by Johnny_9
Mon May 18, 2015 6:28 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 107833

Cold Start - Air Flow

Can we have some more control of cold start air flow (like HP Tuners)

I am assuming the IACV slider/Post Start Fuel does not address this (or does it?)

I guess with this we would also need to data-logs to show the IACV duty cycle.