Search found 63 matches

by 6spd_ek
Tue Oct 27, 2009 3:09 pm
Forum: K-Pro / KManager
Topic: Cam angle "Jitter"
Replies: 8
Views: 3250

EDIT - I am going to try an rsx-s/ep3 si vtc solenoid as I am running an EP3 harness on a TSX motor with a TSX solenoid. the TSX solenoid is the same part # as the '06+ si but NOT the k20a2 & k20a3 vtc solenoids (before edit) well I am still having major issues with vtc jitter even after cleaning th...
by 6spd_ek
Thu Oct 22, 2009 4:04 pm
Forum: K-Pro Calibrations
Topic: Help! spark being pulled when trying to tune 20 vtc
Replies: 3
Views: 1888

IAT Ignition retard. thanks just reading up - & saw doug or derek posted not to have any negative values - I don't think mine are what values should I try to change them too? I will try a couple different intakes but the EP3 chassis sucks... no place to run a CAI unless I get real creative :wink:
by 6spd_ek
Thu Oct 22, 2009 3:31 pm
Forum: K-Pro Calibrations
Topic: Help! spark being pulled when trying to tune 20 vtc
Replies: 3
Views: 1888

Help! spark being pulled when trying to tune 20 vtc

maps are "spark" conservative can anyone tell me why spark is pulled to 18* ? I was trying to tune fuel on on full 20 vtc run is in the 21 seconds also see the vtc & spark jitterness (after run)? I just cleaned the vtc solenoid & filter screen. I have a new cam sensor but which should I try intake o...
by 6spd_ek
Tue Oct 06, 2009 8:26 pm
Forum: K-Pro / KManager
Topic: Knocks when going over bumps on the road.
Replies: 6
Views: 3218

hate to bring this back from the dead - but did anyone find out if there are any major differences between a2 & a3 knock sensors (& accord/tsx for that matter)?

-thanks
by 6spd_ek
Sun Oct 04, 2009 8:53 pm
Forum: K-Pro / KManager
Topic: CAMCMD spikes to 45 degrees
Replies: 1
Views: 1164

CAMCMD spikes to 45 degrees

This has happened on 2 completely different .kals -the vtc spikes b/c the command spikes to 45 degrees. this is on a stock TSX motor in a EP3 running k-manager 1.3.7.0 no where on any maps is vtc more than 30 I have datalogs of both tunes when it occured & as well as the .kals. the newest datalog fr...
by 6spd_ek
Sun Oct 04, 2009 8:40 pm
Forum: K-Pro Calibrations
Topic: VTC or K-Pro Issue?
Replies: 5
Views: 3425

I am having the exact same issue with a STOCK TSX motor. none of my maps have more than 30 vtc yet the cam cmd spikes to 45 my actual jumps to 25 (limited by stock TSX intake cam gear)... two separate times more than 4 minutes into the log could I have a sensor going bad? this is a 2nd completely di...
by 6spd_ek
Sat Oct 03, 2009 8:14 pm
Forum: K-Pro Calibrations
Topic: Help! car dies on same hill in 3rd (kal & datalog inside
Replies: 8
Views: 2651

started over with a new basemap (using hondata's 04-05 tsx stock .kal) & adjusted a/f. so far so good. car runs much smoother I hope to dyno on tuesday but currently knock is disabled. I have a new oem PRB (k20a2) knock sensor but I am not sure if I can use it on a TSX motor running what I believe t...
by 6spd_ek
Fri Oct 02, 2009 7:48 pm
Forum: K-Pro Calibrations
Topic: Help! car dies on same hill in 3rd (kal & datalog inside
Replies: 8
Views: 2651

where are you located? who tuned the car? car needs tuning. i am in upstate NY... The car was dyno tuned sometime ago & then the o2 crapped out. i just replaced it with an OEM honda one (which was in a PRB box), after replacing it I had the car street tuned. also the muffler is starting to fall apa...
by 6spd_ek
Fri Oct 02, 2009 6:09 pm
Forum: K-Pro Calibrations
Topic: Help! car dies on same hill in 3rd (kal & datalog inside
Replies: 8
Views: 2651

with lean protection off my motor didn't die out this time. any clue why or what I can change? dont I want lean protection on? thanks again... attached is new datalog with lean protection off. the same hill is at 1:03 also is the vtc sweep common at 0:59 (command goes to 45vtc - remember I have a st...
by 6spd_ek
Fri Oct 02, 2009 4:56 pm
Forum: K-Pro Calibrations
Topic: Help! car dies on same hill in 3rd (kal & datalog inside
Replies: 8
Views: 2651

will try & I'll datalog... give me a lil bit its pooring rain out right now

thank you

I will cut the datalogging time-frame down too.
by 6spd_ek
Fri Oct 02, 2009 4:23 pm
Forum: K-Pro Calibrations
Topic: Help! car dies on same hill in 3rd (kal & datalog inside
Replies: 8
Views: 2651

sorry I guess I wasn't clear starts @ 5:11 ends near 5:12.5 I think it this case I should start by checking for loose wires & checking fuel lines (any tips appreciated). but it cant hurt to have someone look at the datalog. The car's power stumbles hard at 5:11 at 5:12.5 I start my downshift to 2nd ...
by 6spd_ek
Fri Oct 02, 2009 3:58 pm
Forum: K-Pro Calibrations
Topic: Help! car dies on same hill in 3rd (kal & datalog inside
Replies: 8
Views: 2651

Help! car dies on same hill in 3rd (kal & datalog inside

I could use some help here. My car dies the same time after rounding a right hand turn & going up a hill. I live on the hill so its tough to avoid I see "injector ms" & "injector duty" drop to 0%!!!! (when this occurs @ 5:11) EDIT: the car has always had a full tank of gas my guess is it may not be ...
by 6spd_ek
Tue Sep 08, 2009 5:25 pm
Forum: K-Pro / KManager
Topic: TPS question
Replies: 8
Views: 2283

cool the k24a4 accords (early models pre '05 i believe) open the same direction
by 6spd_ek
Mon Sep 07, 2009 7:22 pm
Forum: K-Pro / KManager
Topic: TPS question
Replies: 8
Views: 2283

what about an older k24a4 or a1 (accord/element/crv)? could one of those TPS be interchangeable?
by 6spd_ek
Sun Apr 19, 2009 7:02 pm
Forum: K-Pro Calibrations
Topic: K20A JDM DC5 CALIBRATION NEEDED
Replies: 14
Views: 8214

the graph & kal posted I had 3ft of 3" pipe off the header :shock: I think my dynojet 230whp was std not sae later on I did add a full kteller/burns stainless 3" exh with a 24" resonator & short muffler & made the same power. eventually (with full 3") I switched IM's to a custom IM & 70mm TB & made ...