Search found 46 matches

by silverspoon1996
Tue Jul 21, 2009 6:06 pm
Forum: Civic Si 2006-2011 Americas
Topic: Fuel: IAT Compensation
Replies: 7
Views: 2791

ok, do you guys think IAT compensation control will ever make it into flashpro manager?
by silverspoon1996
Mon Jul 20, 2009 12:29 pm
Forum: Civic Si 2006-2011 Americas
Topic: Fuel: IAT Compensation
Replies: 7
Views: 2791

Doug,
Do you know off hand what the incriments are... when I was dyno tuned My IAT were around 83-87 during normal driving its around 103-108, and it is not compensating enough...

I am using the RDX start up map, and its dynopack tuned.
by silverspoon1996
Sun Jul 19, 2009 8:04 am
Forum: Civic Si 2006-2011 Americas
Topic: Fuel: IAT Compensation
Replies: 7
Views: 2791

Fuel: IAT Compensation

Is there any IAT compensation for fuel on flashpro??
by silverspoon1996
Sun Jul 19, 2009 1:47 am
Forum: Civic Si 2006-2011 Americas
Topic: Hytech Cams Header 12+ compression and more
Replies: 1
Views: 1667

Hytech Cams Header 12+ compression and more

MODS: 86x86 Stock Block Supertech 12.1:1 pistons Eagle Rods Mugen Head Gasket Endyn Port and polished head Supertech Valvetrain Hytech Stage 1 Camshafts RRC intake Manifold RRC Throttle Body Hytech 4-2-1 Header Hytech 2.5in Exhaust Hytech Renault Cat Converter (100% functional) Flashpro tuner Car Dy...
by silverspoon1996
Sun Jul 12, 2009 4:04 am
Forum: FlashPro Calibrations
Topic: raised compression over 12:1.
Replies: 4
Views: 3805

I figured out part of the problem... I was 2 quarts low on oil from all the revving I had been doing lately... It fixed the hesitation. I am still however getting up to 6 degrees knock retard.
by silverspoon1996
Sun Jul 12, 2009 3:59 am
Forum: Civic Si 2006-2011 Americas
Topic: RDX Injectors
Replies: 6
Views: 3991

how do you pull 10% at idle??? 410 x 90%= 369 stock is 370cc. is this correct?
by silverspoon1996
Sat Jul 11, 2009 1:48 pm
Forum: Civic Si 2006-2011 Americas
Topic: RDX Injectors
Replies: 6
Views: 3991

RDX Injectors

Can I just change in the settings the current injector size to 410, and then tune a/f?
by silverspoon1996
Tue Jul 07, 2009 2:50 pm
Forum: Civic Si 2006-2011 Americas
Topic: Knock retard under WOT
Replies: 6
Views: 2788

I am using the Basemap on MAP setting, for K&n intake, raceheader, and stock exhaust.

I am currently 12.1:1 compression with hytech cams. Is there a basemap with less timing and more fuel??

I posted my datalog in the calibration request part of the forum.
by silverspoon1996
Mon Jul 06, 2009 5:17 pm
Forum: FlashPro Calibrations
Topic: raised compression over 12:1.
Replies: 4
Views: 3805

That sounds all fine but im not a tuner, I am just looking for a basemap to drive to the tuner. As of right now im using the race map on map setting for the K&N v2 and RH. I am going to attach my datalog so someone can take a look it breaks up in first gear and has a hessitation around 3000 rpm.
by silverspoon1996
Mon Jul 06, 2009 3:28 pm
Forum: FlashPro Calibrations
Topic: raised compression over 12:1.
Replies: 4
Views: 3805

raised compression over 12:1.

Is it possible to get a basemap for higher compression?? I am knocking off idle and cant figure it out.
by silverspoon1996
Mon Jul 06, 2009 3:13 pm
Forum: Civic Si 2006-2011 Americas
Topic: Knock retard under WOT
Replies: 6
Views: 2788

i tried retarding sometiming it just made the car run like garbage. Is there a possible way to get a FPCal for higher compression?? IE an altered ignition table.
by silverspoon1996
Sun Jul 05, 2009 5:19 am
Forum: FlashPro Calibrations
Topic: the 410 basemap
Replies: 0
Views: 3056

the 410 basemap

was it intended for a K24?? When I took a look at the cam angle map, I noticed it didnt go over 35 degrees. If so can I just copy the K20 cam angles over??
by silverspoon1996
Sat Jul 04, 2009 10:16 am
Forum: Civic Si 2006-2011 Americas
Topic: Knock retard under WOT
Replies: 6
Views: 2788

Knock retard under WOT

I have a flat 2 degrees with two little spots where it goes to 3 degrees knock retard. Is this ok or should I be retarding timing 2-3 degree?
by silverspoon1996
Wed Jul 01, 2009 5:35 pm
Forum: FlashPro Calibrations
Topic: RDX Injectors
Replies: 2
Views: 3738

ok thank you.
by silverspoon1996
Wed Jul 01, 2009 3:36 pm
Forum: FlashPro Calibrations
Topic: RDX Injectors
Replies: 2
Views: 3738

RDX Injectors

I just Bought RDX injectors and plan on installing them at my house before I get tuned.. How safe is the base map for driving 3 hours to a tuner??

I am running 12:1+ Compression pistons and Hytech Stage 1 cams.