Search found 499 matches

by keto06
Fri Dec 04, 2009 11:57 pm
Forum: K-Pro Calibrations
Topic: Cranny can you please check datalog
Replies: 37
Views: 9546

I must have missed where it said 06 TSX cams where installed. I have a good map I made for an 06 TSX so maybe you can try that one. The only problem is I think this motor was in an RSX, so you will need to copy and paste the maps into a TSX map or just copy the highcam tables into SlipAngles map. Th...
by keto06
Fri Dec 04, 2009 3:28 pm
Forum: K-Pro Calibrations
Topic: Cranny can you please check datalog
Replies: 37
Views: 9546

Keto, anyone that would like to help me is invited to. So thanks to everyone. Thought I would post this http://www.k20a.org/forum/showthread.php?t=67739 Like I said, if Slip_Angle has a lot of work into his, and since his is similar to that one, I recommend using it. Though I would try the kal it r...
by keto06
Fri Dec 04, 2009 2:05 pm
Forum: K-Pro Calibrations
Topic: Cranny can you please check datalog
Replies: 37
Views: 9546

Ok. So I know my opinion means very little but I wanted to say something. I used the Razdyno program and compensated for the weight of the TSX and the gear ratios and then graphed it and although the numbers are prolly off, the one thing that showed was the torque drop off is pretty serious from aro...
by keto06
Thu Dec 03, 2009 11:14 am
Forum: K-Pro Calibrations
Topic: K20Z1 best calibration please
Replies: 39
Views: 11209

Same story. Load this one. Do a datalog. Post it up. Anything else, you're on your own.
by keto06
Sun Nov 29, 2009 12:32 pm
Forum: K-Pro Calibrations
Topic: kal needed for CTR
Replies: 5
Views: 2051

oh well dont put that map on there until you do or add a bunch of fuel to the highcam....
by keto06
Sun Nov 29, 2009 11:08 am
Forum: K-Pro Calibrations
Topic: kal needed for CTR
Replies: 5
Views: 2051

try it and do a datalog and post it up. make sure to get good long 3rd gear runs at FULL WOT. Enable Lean Protection.
by keto06
Sun Nov 29, 2009 10:05 am
Forum: K-Pro Calibrations
Topic: kal needed for CTR
Replies: 5
Views: 2051

so do you want a kal for the PRC mani or the RBC Mani?
by keto06
Sat Nov 28, 2009 11:24 pm
Forum: K-Pro Calibrations
Topic: Cranny can you please check datalog
Replies: 37
Views: 9546

cranny wrote:always keep the newest version yes.

made a couple changes to the cam angles. see if it feels any better to you. your fuel is pretty good , part throttle and WOT.
The funny part about that map is that its almost identical cam angles to the theta dyno tuned k20a2 map I have. How weird right?
by keto06
Sun Nov 22, 2009 11:08 pm
Forum: K-Pro Calibrations
Topic: K24 TSX
Replies: 1
Views: 1446

do more research and then try again
by keto06
Sat Nov 21, 2009 5:06 pm
Forum: K-Pro Calibrations
Topic: DC5 k24a1 BLOCK W/ K20A2 HEAD - NEED GOOD CALIBRATION
Replies: 1
Views: 1662

This may or may not work, I dunno.

But give it a try and post a datalog.
by keto06
Thu Nov 19, 2009 1:27 pm
Forum: K-Pro Calibrations
Topic: ukdm ep3 turbo map
Replies: 12
Views: 3317

I cant figure out how to open two windows.

I just use the Reopen to click between the two since it stays in the same cam angle so I can copy and paste/
by keto06
Wed Nov 18, 2009 4:03 pm
Forum: K-Pro Calibrations
Topic: ukdm ep3 turbo map
Replies: 12
Views: 3317

Yes the PRB uses wideband, hence why i suggested copying that map into PRA tables.

And I know you understood that it was not a load and go scenario.

Copy each of the 26 tables (12+12+2) into a PRA map and do a run and post a datalog.
by keto06
Mon Nov 16, 2009 5:09 pm
Forum: K-Pro Calibrations
Topic: ukdm ep3 turbo map
Replies: 12
Views: 3317

what you should do is copy and paste those maps into a PRA map in KPro to make sure it works.
by keto06
Sun Nov 15, 2009 10:41 am
Forum: K-Pro Calibrations
Topic: VTC or K-Pro Issue?
Replies: 5
Views: 3391

send me a PM and I will help you.
by keto06
Thu Nov 12, 2009 5:51 pm
Forum: K-Pro Calibrations
Topic: '06 TSX intake cam in a 2004 k24a2
Replies: 6
Views: 3549

well i found an article where hondata tuned a car with an 06 intake cam and it was fine to 45 degrees. I emailed them and you should too :P