Search found 420 matches
- Sat Apr 06, 2019 7:39 pm
- Forum: K-Pro / KManager
- Topic: K20 no start with correct injector sizing
- Replies: 4
- Views: 2088
Re: K20 no start with correct injector sizing
Did you set the dead time for the injectors you are using
- Fri Apr 05, 2019 6:51 pm
- Forum: K-Pro / KManager
- Topic: Kpro4 Alternate Speed Input
- Replies: 18
- Views: 11932
Re: Kpro4 Alternate Speed Input
I am having problem with my alternate speed set-up. The input works but when viewing the datalog my gear is not switching and I am also getting a VSS error.
Vehicle: 92 Honda Civic
Serial No.48439
Version:4.4.0
ECU:37820-PND-A55
Engine: JDM K20A (K20A3)
Vehicle: 92 Honda Civic
Serial No.48439
Version:4.4.0
ECU:37820-PND-A55
Engine: JDM K20A (K20A3)
- Fri Mar 15, 2019 11:29 am
- Forum: K-Pro / KManager
- Topic: Kpro4 Alternate Speed Input
- Replies: 18
- Views: 11932
Re: Kpro4 Alternate Speed Input
Using the VSS input for the alternate speed on kpro 4 will the ECU know what gear you are in ?
- Wed Dec 19, 2018 12:21 pm
- Forum: s300 / SManager
- Topic: Low/high load ect fuel comp
- Replies: 30
- Views: 6755
Re: Low/high load ect fuel comp
Post current calibration and a datalog that shows the issue you are having
- Mon Dec 17, 2018 2:44 pm
- Forum: K-Pro / KManager
- Topic: Kpro - K24 Idle drop and instability, tried everything....
- Replies: 22
- Views: 11557
Re: Kpro - K24 Idle drop and instability, tried everything....
Is your fuel pressure ok?
What's the pressure when this is happening
What's the pressure when this is happening
- Sun Dec 16, 2018 4:01 pm
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
Did you rewire the fuel pump?
Did you increase the dead time below 13 volts?
If so what was the result?
ELD is one of the recommended inputs
Did you increase the dead time below 13 volts?
If so what was the result?
ELD is one of the recommended inputs
- Thu Dec 13, 2018 11:50 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
That is a good thing to always do
- Thu Dec 13, 2018 9:49 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
I think that should help
- Thu Dec 13, 2018 7:40 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
The highest I see it went was 1.01, try increasing the voltage below 13.96 by 0.02 and see if that helps with the AF with load.
- Wed Dec 12, 2018 7:35 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
If the fuel pressure is really 45psid then it should look like this
- Wed Dec 12, 2018 7:16 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
- Wed Dec 12, 2018 7:01 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
Check fuel pump voltage and fuel pressure
- Wed Dec 12, 2018 6:38 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
Try running in open loop and note the AF, is it rich or lean?
Also provide a datalog and current Calibration of the open loop operation.
Also provide a datalog and current Calibration of the open loop operation.
- Mon Dec 10, 2018 10:24 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
I Also notice the fuel trims are removing around 12% of fuel, was the car tuned in open loop before it was set to close loop?
- Mon Dec 10, 2018 8:24 am
- Forum: S300 Calibrations
- Topic: leaning out during idle
- Replies: 29
- Views: 14047
Re: leaning out during idle
Did you set the injector deadtime?
What's the fuel pressure?
What's the fuel pressure?