Ok, so there is no harm in creating a linear throttle table? Would I just expect less smoothness and possible more jerkiness?
Is this something that would help with DBW lag?
Search found 145 matches
- Thu Aug 12, 2010 9:57 am
- Forum: FlashPro Manager
- Topic: Why are throttle tables different for different calibrations
- Replies: 3
- Views: 2221
- Wed Aug 11, 2010 3:37 pm
- Forum: FlashPro Manager
- Topic: k20z2
- Replies: 10
- Views: 6227
K20Z2 Found in: 2006- Acura CSX (Canada) Displacement: 1,998 cc (121.9 cu in) Compression: 9.6:1 Power: 155 hp (114 kW) @ 6000 rpm (SAE net J1349 Rev 8/04) Torque: 139 ft·lbf (188 N·m) @ 4500 rpm Redline: 6800 rpm 2006- Honda Civic (JDM) Displacement: 1,998 cc (121.9 cu in) Compression: 9.6:1 Power:...
- Tue Aug 10, 2010 12:33 pm
- Forum: FlashPro Manager
- Topic: Why are throttle tables different for different calibrations
- Replies: 3
- Views: 2221
Why are throttle tables different for different calibrations
Some people say the flashpro increases throttle response and helps the lag inherent to this drive by wire system. I don't see how it does this. I started looking at the throttle tables in different calibrations within the software and there are vastly different setups in the cals that come with the ...
- Mon Aug 09, 2010 8:47 am
- Forum: FlashPro Manager
- Topic: closed loop target and acceleration enrichment
- Replies: 1
- Views: 1759
- Wed Jul 14, 2010 1:31 pm
- Forum: FlashPro Manager
- Topic: idle with AC on problem
- Replies: 8
- Views: 4330
- Sun Jul 11, 2010 6:05 pm
- Forum: FlashPro Manager
- Topic: Boost control by gear with different gear ratio's
- Replies: 11
- Views: 7110
- Thu Jun 17, 2010 7:35 pm
- Forum: FlashPro Manager
- Topic: Tip for boost control duty cycles and temp. compensation
- Replies: 4
- Views: 5031
- Fri Jun 11, 2010 9:14 pm
- Forum: FlashPro Manager
- Topic: Tip for boost control duty cycles and temp. compensation
- Replies: 4
- Views: 5031
Couple questions then. I have a 4.35psi small red tial spring. I got up to 19.5 psi during my tuning I was using a manual boost controller for tuning. What would 100% duty cycle give me? I thought you could only go about triple your wastegate spring? If I want to use my manifold vaccuum instead of t...
- Wed Jun 09, 2010 4:31 pm
- Forum: FlashPro Manager
- Topic: Tip for boost control duty cycles and temp. compensation
- Replies: 4
- Views: 5031
Tip for boost control duty cycles and temp. compensation
Hondata do you have any tips for setting up boost control duty cycles? I've noticed that in lower gears you need to have higher BC duty cycles to achieve the same boost in 3rd or 4th gears. i.e. 35% duty cycle gave me 9 psi in 2nd gear and around 16psi in 4th. Does the frequency have anything to do ...
- Wed May 26, 2010 8:04 pm
- Forum: Civic Si 2006-2011 Americas
- Topic: wire connector for the ECU harness for boost solenoid?
- Replies: 1
- Views: 2464
wire connector for the ECU harness for boost solenoid?
Can't find the little wire connector anywhere that goes into the ECU harness that accepts the pin from the ECU to wire up the boost control solenoid. Does anyone know what it's called or where I can get it. Radioshack and home depot and walmart did not have them. Are they called BEC or jst connector...