Search found 116 matches
- Tue Sep 30, 2014 6:44 pm
- Forum: s300 / SManager
- Topic: S300 ECU just died
- Replies: 8
- Views: 5373
Re: S300 ECU just died
v2.3.3.0
- Mon Sep 29, 2014 6:48 pm
- Forum: s300 / SManager
- Topic: S300 ECU just died
- Replies: 8
- Views: 5373
S300 ECU just died
Driving home from work and while decelerating for a red light the car turns off with a solid CE light. It cranks but won't start. Since I resell, chip, tune and repair OBD1 ECUs, I pull a customers ECU from the trunk and the car starts right up. I drive to the nearest gas station to troubleshoot the...
- Sun Sep 14, 2014 5:13 am
- Forum: s300 / SManager
- Topic: S300 v1 #0898 solid D1 light
- Replies: 3
- Views: 2858
Re: S300 v1 #0898 solid D1 light
It's an R7 board. I'm not sure if they were copied so I couldn't use your counterfeit fotos to validate. Thanks for your help!
- Sat Sep 06, 2014 2:15 pm
- Forum: s300 / SManager
- Topic: S300 v1 #0898 solid D1 light
- Replies: 3
- Views: 2858
S300 v1 #0898 solid D1 light
Customer brought in his ECU with an S300 v1 board installed for repair. Says the car has a solid cel and runs poorly. Tested the S300 in my own personal ECU which has a V1 board isntalled and working fine but with his board, D1 stays lit solid. Attempts to erase the ECU fails and I cannot upload a c...
- Sat Jul 05, 2014 3:30 pm
- Forum: s300 / SManager
- Topic: Ignition Table & Datalog not the same?
- Replies: 9
- Views: 4297
Re: Ignition Table & Datalog not the same?
Ok attached is a real datalog along with the calibration. Thank you for your assistance.
- Mon Apr 28, 2014 4:43 am
- Forum: s300 / SManager
- Topic: Ignition Table & Datalog not the same?
- Replies: 9
- Views: 4297
Re: Ignition Table & Datalog not the same?
I apologize for not informing you of the SIM and I thought it was a valid test setting the knobs until the sensor readings in the datalog turned "green". I run a speed shop and have been repairing OBD1 ECUs for close to 10 years (since your original Hondata "staged" systems) for ...
- Sun Apr 27, 2014 6:06 am
- Forum: s300 / SManager
- Topic: Ignition Table & Datalog not the same?
- Replies: 9
- Views: 4297
Re: Ignition Table & Datalog not the same?
The ECU is on a moates engine simulator and the knobs are set into the "green" areas for the sensors. Aside from your observations which are valid for a real engine, would this affect the variance between the display end the datalog? If so, how should I set the knobs on the SIM properly as...
- Sun Apr 20, 2014 9:31 am
- Forum: s300 / SManager
- Topic: Ignition Table & Datalog not the same?
- Replies: 9
- Views: 4297
Re: Ignition Table & Datalog not the same?
Attached...
- Sat Apr 19, 2014 5:28 pm
- Forum: s300 / SManager
- Topic: Ignition Table & Datalog not the same?
- Replies: 9
- Views: 4297
Ignition Table & Datalog not the same?
The ignition advance cell value and datalogging table are not the same. Where are all the compensation areas affecting total timing?
- Thu Mar 21, 2013 11:34 am
- Forum: s300 / SManager
- Topic: Tuning on an s300 v1 then moving the cal to an s300 v2
- Replies: 3
- Views: 1763
Re: Tuning on an s300 v1 then moving the cal to an s300 v2
Excellent - thank you. Just to validate, a V1 hardware tune will run exactly the same on V2 hardware.
- Thu Mar 21, 2013 11:00 am
- Forum: s300 / SManager
- Topic: Tuning on an s300 v1 then moving the cal to an s300 v2
- Replies: 3
- Views: 1763
Tuning on an s300 v1 then moving the cal to an s300 v2
If the version of Smanager stays the same, will a calibration created on V1 hardware work on v2 hardware without changes? I was asked this by a client waiting for his v2 board but in the need to tune his car today on v1 hardware and does not want to lose his investment in tuning/dyno time.
- Sat Sep 03, 2011 12:12 pm
- Forum: s300 / SManager
- Topic: Punching Out the USB Hole
- Replies: 2
- Views: 4992
Punching Out the USB Hole
I've been installing several S300's lately and I'm spending too much time punching out the hole with a Dremel (I'm anal about how it looks). Is there anternative/shortcut/better method of preparing the ECU case?
- Mon Feb 21, 2011 5:29 pm
- Forum: s300 / SManager
- Topic: Hondata s300 capacitor value
- Replies: 4
- Views: 1712
- Mon Feb 21, 2011 3:24 pm
- Forum: s300 / SManager
- Topic: Hondata s300 capacitor value
- Replies: 4
- Views: 1712
- Mon Feb 21, 2011 9:26 am
- Forum: s300 / SManager
- Topic: Hondata s300 capacitor value
- Replies: 4
- Views: 1712
Hondata s300 capacitor value
Hi, I just bought a used s300 system from a friend and the surface mount capacitor at position C8 is missing/damaged. Can you tell me the value of this cap so I can replace it? Thanks!
Raul
Raul