Search found 138 matches

by Knox
Sat Dec 27, 2014 10:06 am
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.1

Are you sure? Because it seems like works very well on closed loop. I will test it with innovate lm2 external wideband sensor in two weeks.

civicRSA wrote:Your oxygen sensor is faulty. It is a common problem so don't be surprised if you have the problem on 2 cars.
by Knox
Mon Dec 22, 2014 12:12 pm
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.1

First I think oxygen sensor reading wrong but after I have the same problem with an other fd2 type r which I tuned before without a problem. So I don't think both sensors reading wrong.

Spunkster wrote:Are you sure the oxygen sensor is reading correctly.
by Knox
Mon Dec 22, 2014 12:08 pm
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.1

I will test it with external wideband sensor in a week. If afr will be richer why I can not see it on flaspro manager?

Thanks.

Hondata wrote:If the injector duration increases then there's nothing wrong with the table operation in the ECU.

Please don't downgrade the firmware.
by Knox
Sat Dec 20, 2014 12:16 pm
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.1

here is the second car's datalogs.
by Knox
Sat Dec 20, 2014 12:15 pm
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.1

Yesterday I tried again and I had the same problem again. After that I noticed duty cycle increasing when I added fuel but the air fuel ratio doesn't change at all, I mean for ex I added 30% fuel but air fuel ratio didn't be richer but duty cycle inreased from around 80% to 100%. When I noticed that...
by Knox
Thu Dec 18, 2014 4:52 am
Forum: K-Pro / KManager
Topic: KManager V4.0.7
Replies: 18
Views: 11518

Re: KManager V4.0.3

Is it possible to add rev limit by gear like s300? KManager V4 supports the new KPro4 , which has significant improvements over previous generation KPros, and also adds some new features to the KPro1, KPro2 & KPro3. Changes in 4.0.2: Added KPro4 support [KPro4] Bluetooth [KPro4] Ethanol sensor i...
by Knox
Thu Dec 18, 2014 4:52 am
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.0

When I saw that first engine runing lean like 14s every rpm and cam angle range, I used 'ALL' and added 10% fuel to everywhere, so I don't think I edited only the 0 degree cam table. Anyway tomorrow I will check that car again and take a datalog if problem continue. Ok, then the usual problem is tha...
by Knox
Wed Dec 17, 2014 9:00 am
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.0

After I see that problem with the calibration I make to another car, I tried with 'Hondata FD2 Type R' reflash also (which is hondata base calibration) and I had the same problem again. Short term trim instantly goes to '0' which shows that it is in open loop but the changes I made doesn't effect th...
by Knox
Wed Dec 17, 2014 5:16 am
Forum: FlashPro Manager
Topic: FlashProManager v2.2.8
Replies: 80
Views: 74468

Re: FlashProManager v2.0.0

Today, I tried to mapping a jdm FD2 civic type r with flashpro manager v2.0.0. Everything works right when driving in closed loop but when you full throttle car don't turn to open loop. Short term trim be 0% but it looks like engine runs in open loop because I added 10% fuel but air fuel ratio doesn...
by Knox
Wed Dec 10, 2014 5:36 am
Forum: K-Pro / KManager
Topic: KManager V4.0.7
Replies: 18
Views: 11518

Re: KManager V4.0.2

Today I downloaded the k manager v4.0.2 and upload my calibration to my krpo. After that my car starts to don't activate vtec (vtc working). My car is jdm integra type r with jdm k20a, my kpro is v2 on prb ecu. I datalog the problem which I attached the datalog and calibration and after I uninstall ...
by Knox
Wed Oct 15, 2014 8:02 am
Forum: s300 / SManager
Topic: V3 PLX digital input, daisy chain, and AIM MXL info
Replies: 3
Views: 3002

Re: V3 PLX digital input, daisy chain, and AIM MXL info

seelback wrote:Heres a link to the thread I made for this info in detail.
http://honda-tech.com/showthread.php?t=3203138
great write up, thanks.
by Knox
Tue Oct 07, 2014 11:36 pm
Forum: Civic Type R 2006-2010 Japanese FD2
Topic: boost tables
Replies: 1
Views: 10070

boost tables

when I select the japanese fd2 type r reflash calibration or stock equivalent calibration, there is not boost tables. Can I use "fn2 group n calibration" or "fn2 euro civic type r forced induction starting calibration" on boosted japanese fd2 civic type r?

Thanks.
by Knox
Tue Sep 23, 2014 8:09 am
Forum: K-Pro / KManager
Topic: KPro / KManager requests
Replies: 146
Views: 835088

Re: KPro / KManager requests

Rev limit by gear like s300.

Thanks.
by Knox
Sun Nov 03, 2013 1:35 pm
Forum: K-Pro / KManager
Topic: VTC angle spikes
Replies: 5
Views: 3461

Re: VTC angle spikes

It could be the VTC gear, VTC solenoid, VTC filter, chain / chain tensioner, cams / rockers, VTC wiring or anything which effects the oil pressure. I'd start by checking the VTC filter and then swapping out the VTC solenoid. In a forum, one tuner writes that camshaft postiion sensor also make that ...
by Knox
Tue Oct 08, 2013 11:29 am
Forum: K-Pro / KManager
Topic: VTC angle spikes
Replies: 5
Views: 3461

Re: VTC angle spikes

It could be the VTC gear, VTC solenoid, VTC filter, chain / chain tensioner, cams / rockers, VTC wiring or anything which effects the oil pressure. I'd start by checking the VTC filter and then swapping out the VTC solenoid. In a forum, one tuner writes that camshaft postiion sensor also make that ...