Search found 98 matches
- Sat Jan 11, 2020 5:42 pm
- Forum: K-Pro / KManager
- Topic: Plx dm6 to prb kpro v4 ep3
- Replies: 11
- Views: 2708
Re: Plx dm6 to prb kpro v4 ep3
I+ and G on the kpro board connects to TX on the PLX module.
- Wed Dec 11, 2019 9:56 am
- Forum: K-Pro / KManager
- Topic: Plx dm6 to prb kpro v4 ep3
- Replies: 11
- Views: 2708
Re: Plx dm6 to prb kpro v4 ep3
Digital input works great as well, I've been running that for years now.
- Mon Nov 04, 2019 10:27 am
- Forum: K-Pro / KManager
- Topic: Trying to get External Wideband values to match in KManager
- Replies: 2
- Views: 948
Re: Trying to get External Wideband values to match in KManager
You could always use the digital input instead (TTL serial input).
No more problems with voltage offset and if you ad more PLX sensors there is no added wiring needed.
No more problems with voltage offset and if you ad more PLX sensors there is no added wiring needed.
- Fri Oct 04, 2019 6:49 am
- Forum: K-Pro / KManager
- Topic: Rev limiter not working
- Replies: 2
- Views: 1112
Re: Rev limiter not working
Are you looking at the dash or in a log?
The dash can sometimes be a bit off, especially in the higher rpm's.
The dash can sometimes be a bit off, especially in the higher rpm's.
- Wed Sep 18, 2019 9:14 am
- Forum: K-Pro / KManager
- Topic: Constant VSS even at stop; Speed reads wrong. [Ap1/K24]
- Replies: 3
- Views: 1032
Re: Constant VSS even at stop; Speed reads wrong. [Ap1/K24]
With oil temp you mean the stock coolant temp on the dash?
If it's a standard PRB ecu for a k-series car I don't think that will work with the dash, at least not the temp gauge.
There is a special extra circuit board on the S2000 specific kpro.
If it's a standard PRB ecu for a k-series car I don't think that will work with the dash, at least not the temp gauge.
There is a special extra circuit board on the S2000 specific kpro.
- Mon May 20, 2019 5:52 am
- Forum: K-Pro / KManager
- Topic: PLX WideBand and Kpro3 issues
- Replies: 9
- Views: 1833
Re: PLX WideBand and Kpro3 issues
I would use a multimeter and check that the PLX box is actually outputting any signal.
- Mon May 20, 2019 3:10 am
- Forum: K-Pro / KManager
- Topic: PLX WideBand and Kpro3 issues
- Replies: 9
- Views: 1833
Re: PLX WideBand and Kpro3 issues
Did you ad the settings for the analog 0 channel like explained here?
https://www.hondata.com/help/kmanager/i ... inputs.htm
https://www.hondata.com/help/kmanager/i ... inputs.htm
- Sun May 19, 2019 2:19 pm
- Forum: K-Pro / KManager
- Topic: PRA Kpro V4 wideband support
- Replies: 1
- Views: 981
Re: PRA Kpro V4 wideband support
You are correct.
I can recommend the PLX one, I have used one of those for a few years now and it's working great.
Using the digital connection only.
I can recommend the PLX one, I have used one of those for a few years now and it's working great.
Using the digital connection only.
- Thu May 16, 2019 2:30 pm
- Forum: K-Pro / KManager
- Topic: Fuel overrun cutoff
- Replies: 7
- Views: 2638
Re: Fuel overrun cutoff
Thanks for the tip on trimming the logs. I made it much smaller now and it should be pretty clear now if you check what is happening at 1:02 1:20 1:31 mark Please check the behavior on the "rev limit sensor" as well, every time the injectors shut off it seems the rev limiter is ON. And yes...
- Wed May 15, 2019 10:07 am
- Forum: K-Pro / KManager
- Topic: Fuel overrun cutoff
- Replies: 7
- Views: 2638
Re: Fuel overrun cutoff
I know, but I have a very effective vacuum block which you could probably see in the log so please disregard this.
What is the minimum delay for the fuel overrun cutoff? Is half a second normal or should it be lower?
Also if you could answer my question about the rev limit sensor that would be great.
What is the minimum delay for the fuel overrun cutoff? Is half a second normal or should it be lower?
Also if you could answer my question about the rev limit sensor that would be great.
- Tue May 14, 2019 10:58 pm
- Forum: K-Pro / KManager
- Topic: Fuel overrun cutoff
- Replies: 7
- Views: 2638
Re: Fuel overrun cutoff
Because MAP based works pretty good and was much easier to tune.
Would an alpha-n tune make a difference regarding this specific issue?
Would an alpha-n tune make a difference regarding this specific issue?
- Tue May 14, 2019 1:40 pm
- Forum: K-Pro / KManager
- Topic: Fuel overrun cutoff
- Replies: 7
- Views: 2638
Fuel overrun cutoff
I'm not sure if I have a real problem but I'm wondering if there's always going to be a delay before the injectors are shut off? All or almost every time I let off the throttle I'm seeing a full rich condition and I can see the injectors are still spraying. I haven't thought to much about it before ...
- Mon Apr 29, 2019 2:05 pm
- Forum: Hondata Mobile
- Topic: Hondata Mobile Apps
- Replies: 15
- Views: 20367
Re: Hondata Mobile Apps
Are there not going to be any more updates on the old free version?
Is there a list of track circuits available in the new app, can you ad ones yourself?
Is there a list of track circuits available in the new app, can you ad ones yourself?
- Mon Jan 21, 2019 12:28 am
- Forum: K-Pro / KManager
- Topic: Is RSX pseudo wideband O2 capable for E85 supercharged?
- Replies: 2
- Views: 847
Re: Is RSX pseudo wideband O2 capable for E85 supercharged?
Do you got the sensor installed and working?
I think you need to do some substantial re-wiring to get it up and running in a S2000 setup.
I think you need to do some substantial re-wiring to get it up and running in a S2000 setup.
- Thu Dec 27, 2018 5:30 pm
- Forum: K-Pro / KManager
- Topic: Just about starts, revs to 2500, dies
- Replies: 2
- Views: 1265
Re: Just about starts, revs to 2500, dies
You need to use a correct and working O2 sensor, not sure a PRA calibration works on a PRB ecu either.
Why not get a RSX wideband O2 sensor and keep the PRB ecu you got now?
Why not get a RSX wideband O2 sensor and keep the PRB ecu you got now?