Hondata

Hondata User Forum
It is currently Sun May 19, 2013 2:25 am

View unanswered posts | View active topics


Board index » K-Series » K-Pro / KManager

All times are UTC - 8 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 13 posts ] 
  Previous topic | Next topic 
Author Message
himsweet66six
 Post subject: P0010
PostPosted: Fri Jul 06, 2012 8:09 pm 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
ok here is the run down of my problem. current setup. 05 type s with full k24a2 swap. previously i was using a kpro prc ecu with the 05 jumper harness. car ran fine and never threw this code. i recently swapped my ecu for a kpro prb ecu. everything seems to run fine but when i give it gas it throws the p0010 code. i just bought a brand new vtc solenoid hoping it would fix the problem but it threw the same code again. i am not sure what is happening or how to fix this. does anyone have any insight?
Top
 Profile  
 
Spunkster
 Post subject: Re: P0010
PostPosted: Mon Jul 09, 2012 10:19 am 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11057
Location: Hondata
What is the serial number of the K-Pro board inside the ECU?
Top
 Profile  
 
himsweet66six
 Post subject: Re: P0010
PostPosted: Mon Jul 09, 2012 6:02 pm 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
Spunkster wrote:
What is the serial number of the K-Pro board inside the ECU?


05003782
Top
 Profile  
 
Spunkster
 Post subject: Re: P0010
PostPosted: Tue Jul 10, 2012 9:20 am 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11057
Location: Hondata
This ECU is not designed for running with an adapter harness. The 05-06 adapter harness is only for use in an 05-06 RSX and is not for use with engine swaps.
Top
 Profile  
 
himsweet66six
 Post subject: Re: P0010
PostPosted: Tue Jul 10, 2012 10:31 am 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
Ok so how can I get this to work? Can I ground the vtc(-) to the chassis or run a wire to splice into the correct wire on the harness?
Top
 Profile  
 
Spunkster
 Post subject: Re: P0010
PostPosted: Tue Jul 10, 2012 1:16 pm 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11057
Location: Hondata
The ECU would have to be sent in to be upgraded to work in an 05-06 RSX. The cost for this is $250. You would have to fill out the K-Pro form and note what it is you want done and include a cashier's check for the full amount.
Top
 Profile  
 
himsweet66six
 Post subject: Re: P0010
PostPosted: Tue Jul 10, 2012 5:05 pm 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
Spunkster wrote:
The ECU would have to be sent in to be upgraded to work in an 05-06 RSX. The cost for this is $250. You would have to fill out the K-Pro form and note what it is you want done and include a cashier's check for the full amount.


so its not possible to just ground out the sensor? I dont understand how my kpro prc ecu was able to run fine.
Top
 Profile  
 
Spunkster
 Post subject: Re: P0010
PostPosted: Wed Jul 11, 2012 4:04 pm 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11057
Location: Hondata
No the only solution is what I mentioned above.
Top
 Profile  
 
himsweet66six
 Post subject: Re: P0010
PostPosted: Wed Jul 11, 2012 4:57 pm 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
Spunkster wrote:
No the only solution is what I mentioned above.


ok well i have an eps setup in my car with a dakota speed converter will this be affected if i do this upgrade?
Top
 Profile  
 
himsweet66six
 Post subject: Re: P0010
PostPosted: Mon Jul 16, 2012 11:36 am 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
I looked at the form and was confused as to who i should send my ecu to. do i send it directly to hondata? also do i just state that i need the ecu to be compatible with an 05 rsx type s with a k24a2 swap? let me know so i can send this out.
Top
 Profile  
 
Spunkster
 Post subject: Re: P0010
PostPosted: Mon Jul 16, 2012 4:26 pm 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11057
Location: Hondata
Fill out the from at http://www.hondata.com/kproecuinfoform.html

Choose the option for the 05-06 K-Pro. Y0u must include a cashier's check for $250
Top
 Profile  
 
himsweet66six
 Post subject: Re: P0010
PostPosted: Tue Aug 14, 2012 9:08 am 
Offline

Joined: Tue Aug 07, 2007 7:49 pm
Posts: 12
just got my ecu back. also came with a 05-06 wiring harness. now i already have an 05-06 harness, but i need to know if there is any differance between my older harness and the new one i just received. thanks in advance for the response.
Top
 Profile  
 
Spunkster
 Post subject: Re: P0010
PostPosted: Tue Aug 14, 2012 10:54 am 
Offline
Site Admin
User avatar

Joined: Fri Sep 20, 2002 5:06 pm
Posts: 11057
Location: Hondata
The other harness may have been counterfeit.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 13 posts ] 

Board index » K-Series » K-Pro / KManager

All times are UTC - 8 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group