KPRO V4 phantom CEL No Codes

K-Series Programmable ECU installation questions / support issues
Post Reply
Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

KPRO V4 phantom CEL No Codes

Post by Juncura1 » Tue Jun 11, 2019 11:15 am

KPro Version 4
Vehicle: 2000 Honda S2000
Serial Number: 41538
Firmware Version: 12.00
Software Version: 4.4.1.0

Recently, I've been having a strange issue with the CEL being illuminated with no codes. The issue only occurs after driving the car until fully warm, shutting off and then starting again when warm.

Example: I start the car in the morning after sitting overnight and drive the car for 20-30min to the store. Park the car for 20-30min and then drive home... after about 5min into the drive home the CEL will illuminate with no codes. If I use the app on my phone, and hit the "Delete" button, the CEL will turn off. If I'm datalogging and erase DTC's the CEL will turn off.

I've attached my calibration as well as a short log while the CEL was on.
Attachments
Datalog-190611-000.kdl
(251.73 KiB) Downloaded 16 times
AP1-AdaptedModified LC 4600VTEC + 4degIgnTaper.kal
(161.91 KiB) Downloaded 17 times

User avatar
Spunkster
Site Admin
Posts: 17864
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KPRO V4 phantom CEL No Codes

Post by Spunkster » Tue Jun 11, 2019 11:40 am

Try going to the online menu and then go to tools and then erase the ECU. When that finishes, close the program, reopen the program, load your calibration and then upload to the ECU and see if the problem persists.

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Tue Jun 11, 2019 11:44 am

I'll give it a try and report back.

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Tue Jun 11, 2019 2:44 pm

Spunkster wrote:
Tue Jun 11, 2019 11:40 am
Try going to the online menu and then go to tools and then erase the ECU. When that finishes, close the program, reopen the program, load your calibration and then upload to the ECU and see if the problem persists.
Erasing the ECU did not help.

User avatar
Spunkster
Site Admin
Posts: 17864
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KPRO V4 phantom CEL No Codes

Post by Spunkster » Tue Jun 11, 2019 3:02 pm

Is it running normally when the CEL is on?

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Tue Jun 11, 2019 3:16 pm

Spunkster wrote:
Tue Jun 11, 2019 3:02 pm
Is it running normally when the CEL is on?
It doesn't seem to be according to the logs, but it does "feel" a bit sluggish or down on power. However, the logs don't show any change so it could be in my head. Without renting dyno time I can't say for sure,

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Tue Jun 11, 2019 3:17 pm

Spunkster wrote:
Tue Jun 11, 2019 3:02 pm
Is it running normally when the CEL is on?
It doesn't seem to be according to the logs, but it does "feel" a bit sluggish or down on power. However, the logs don't show any change so it could be in my head.

User avatar
Spunkster
Site Admin
Posts: 17864
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KPRO V4 phantom CEL No Codes

Post by Spunkster » Tue Jun 11, 2019 4:29 pm

Can you try and Datalog before this happens and catch it actually come on in the middle of the Datalog and send that Datalog to us.
IF you know roughly when in the Datalog occurs, please let us know that timestamp.

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Tue Jun 11, 2019 4:54 pm

I'll get that to you as soon as I can.

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Wed Jun 12, 2019 4:00 pm

Here is the datalog.

I started with a fresh calibration and was tuning the fuel tables when the event occurred. I marked the event by going WOT a second or two after the light came on.
Attachments
Datalog-190612-011.kdl
(989.09 KiB) Downloaded 18 times

User avatar
Spunkster
Site Admin
Posts: 17864
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KPRO V4 phantom CEL No Codes

Post by Spunkster » Wed Jun 12, 2019 4:51 pm

There is an error code at that time P0131

Juncura1
Posts: 17
Joined: Sat Mar 23, 2019 4:43 pm

Re: KPRO V4 phantom CEL No Codes

Post by Juncura1 » Wed Jun 12, 2019 5:34 pm

Okay. Any ideas of why I am unable to see it?

User avatar
Spunkster
Site Admin
Posts: 17864
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KPRO V4 phantom CEL No Codes

Post by Spunkster » Thu Jun 13, 2019 9:29 am

It is in the Datalog you posted, look near the end of the Datalog.

Post Reply