Kpro in Tube frame with JDM motor

K-Series Programmable ECU installation questions / support issues
Post Reply
Underdog51
Posts: 8
Joined: Fri Jun 21, 2019 3:20 pm

Kpro in Tube frame with JDM motor

Post by Underdog51 » Mon Jun 24, 2019 2:43 pm

I am not sure if this is the correct section, I am new to this Hondata world.
I have a confusing setup and need some advice on what type of calibration/wiring I should be running.
Car is a tube frame race car (Stalker Cars AXR)
Engine is k20A2 from JDM Euro R
RWD BMW transmission
ECU is a 05 Acura RSX base Auto
I have converted what I think is all the pins over correctly to a 02-04 wiring. Is this correct even though the ECU is 05?
I will be running a GPS speed sensor for an input.
Fuel pump is running from a toggle switch.
I am not able to get this engine to fire up yet.
Thank you for any help and your patience
Attachments
brianlog.kdl
(475.95 KiB) Downloaded 10 times
Brianbasecalibration.kal
(162.79 KiB) Downloaded 10 times

User avatar
Spunkster
Site Admin
Posts: 17850
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Kpro in Tube frame with JDM motor

Post by Spunkster » Mon Jun 24, 2019 4:26 pm

You cannot use a 05 base auto ECU with a K-Pro. What is your ECU part number?

Underdog51
Posts: 8
Joined: Fri Jun 21, 2019 3:20 pm

Re: Kpro in Tube frame with JDM motor

Post by Underdog51 » Mon Jun 24, 2019 5:34 pm

The website says you can under the "alternate ECU" section. And they did mod it already. It's 37820-pnd-a58 and 2063-806057. Thanks

Underdog51
Posts: 8
Joined: Fri Jun 21, 2019 3:20 pm

Re: Kpro in Tube frame with JDM motor

Post by Underdog51 » Mon Jun 24, 2019 7:30 pm

Latest log and calibration. There were some pins were still off, that are corrected. shouldn't it be reading a CAM angle under cranking? Maybe its a different cam sensor?
Attachments
briantest2.kdl
(352.95 KiB) Downloaded 9 times
Brianbasecalibration.kal
(162.79 KiB) Downloaded 10 times

User avatar
Spunkster
Site Admin
Posts: 17850
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Kpro in Tube frame with JDM motor

Post by Spunkster » Tue Jun 25, 2019 9:04 am

The ECU you have is an 02-04. What harness are you using?

Underdog51
Posts: 8
Joined: Fri Jun 21, 2019 3:20 pm

Re: Kpro in Tube frame with JDM motor

Post by Underdog51 » Tue Jun 25, 2019 10:06 am

I took the JDM harness, removed all the pins out of the ECU connectors. I then repined all the sensors to the correct ECU positions as per information on http://www.phearable.net/information/te ... grams.html
I just replaced the crank and exhaust cam sensor that appeared to be different for normal USA k20. still no go. Here is the latest datalog.
Attachments
afterUSAk20 cam and crank sensor.kdl
(446.48 KiB) Downloaded 13 times

User avatar
Spunkster
Site Admin
Posts: 17850
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Kpro in Tube frame with JDM motor

Post by Spunkster » Tue Jun 25, 2019 11:08 am

I would recommend using an 02-04 RSX engine harness and sensor from an 02-04 RSX.

Underdog51
Posts: 8
Joined: Fri Jun 21, 2019 3:20 pm

Re: Kpro in Tube frame with JDM motor

Post by Underdog51 » Tue Jun 25, 2019 1:24 pm

I just went through and ohm'd every single wire from ecu plug to sensor plug, it is all correct. I would like to try a few things before buying a harness. How can I check the raw data coming in from each sensor? I am trying to figure out this software. I have built over 200 cars from scratch using LS and hp tuner. I am just new to the honda world. thank you very much for your time a patience so far.

User avatar
Spunkster
Site Admin
Posts: 17850
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Kpro in Tube frame with JDM motor

Post by Spunkster » Tue Jun 25, 2019 1:27 pm

You cannot get raw data from the cam and crank sensors from our software. try the ECU on a known working vehicle first. If it works as it should then you have something wired incorrectly or have a mechanical issue.

Underdog51
Posts: 8
Joined: Fri Jun 21, 2019 3:20 pm

Re: Kpro in Tube frame with JDM motor

Post by Underdog51 » Tue Jun 25, 2019 2:22 pm

ok, thank you for your help. I will see what I can find.

Post Reply