new to kpro, please help wideband question
new to kpro, please help wideband question
i am getting kpro soon, i am going to instal a wideband on my car before i recieve the kpro. when people instal the widebands using kpro do they use the wideband output to the kpro input to give it kpro wideband readings?
-
- Posts: 100
- Joined: Tue Jun 07, 2005 3:19 pm
So if you add an aftermarket wideband there is no way to datalog it through k-pro??
I'm confused.
I'm looking at getting an Innovative Wideband because the factory o2 can't read below 11.5. That makes it very hard to tune my nitrous setup since I'm shooting for 11.5-11.7 A/F's.
Is there any way to datalog the aftermarket wideband without messing up your closed loop and lean protection from the primary o2?
I'm confused.
I'm looking at getting an Innovative Wideband because the factory o2 can't read below 11.5. That makes it very hard to tune my nitrous setup since I'm shooting for 11.5-11.7 A/F's.
Is there any way to datalog the aftermarket wideband without messing up your closed loop and lean protection from the primary o2?
03' RSX Type-S
I/H/E/RBC/K-PRO/100shot/555R's
13.2 @ 109mph w/ 2.0 60'
I/H/E/RBC/K-PRO/100shot/555R's
13.2 @ 109mph w/ 2.0 60'
Nope, it can only read to 11.5. This was quoted directly from Hondata's description of K-PRO.
"The stock JDM and US O2 sensor is wide band and can read from 11.5:1 to 30:1 A/F ratios."
So basically, all I have to do is run the output from the Wideband gauge to the ELD pin on the ECU and I'll be able to datalog it's readings, and it wont' effect anything with the primary o2 sensor? It will just be another sensor that I can datalog while in K-PRO. CORRECT???
**EDIT: I just answered my own question. I was messing around with K-PRO and read the HELP section. Basically, when set up properly, you will see the reading of the Aftermarket Wideband in your datalogs. But, K-PRO will still use the primary o2 for Closed Loop Operation. END EDIT**
"The stock JDM and US O2 sensor is wide band and can read from 11.5:1 to 30:1 A/F ratios."
So basically, all I have to do is run the output from the Wideband gauge to the ELD pin on the ECU and I'll be able to datalog it's readings, and it wont' effect anything with the primary o2 sensor? It will just be another sensor that I can datalog while in K-PRO. CORRECT???
**EDIT: I just answered my own question. I was messing around with K-PRO and read the HELP section. Basically, when set up properly, you will see the reading of the Aftermarket Wideband in your datalogs. But, K-PRO will still use the primary o2 for Closed Loop Operation. END EDIT**
03' RSX Type-S
I/H/E/RBC/K-PRO/100shot/555R's
13.2 @ 109mph w/ 2.0 60'
I/H/E/RBC/K-PRO/100shot/555R's
13.2 @ 109mph w/ 2.0 60'
what is there an echo in here? lol. look at my post before yours compared to the one you just made , see any similarities? little repetition perhaps? lol
im not gonna argue with you , but i assure you it can read lower than 11.5. its in the high 10's. unless when i read datalogs they are lying to me , lol.
im not gonna argue with you , but i assure you it can read lower than 11.5. its in the high 10's. unless when i read datalogs they are lying to me , lol.
http://www.hondata.com/kpro.html
Scroll down to General Notes. 8) They specifically state 11.5.
One thing still has me a lil' confused though. When you go into Help in Kmanager, and pull up the Closed Loop Settings, it shows a box that you can check that is called "Datalog ELD Voltage". When I go under Closed Loop to check the box though, it's not there. The only place it's shown is in the Help File. It also says - "not in operation" in the description for it. Does that mean you don't have to check this box when you add a wideband? Just setup the Wideband Lamda Input under the Settings and that's it?
Scroll down to General Notes. 8) They specifically state 11.5.
One thing still has me a lil' confused though. When you go into Help in Kmanager, and pull up the Closed Loop Settings, it shows a box that you can check that is called "Datalog ELD Voltage". When I go under Closed Loop to check the box though, it's not there. The only place it's shown is in the Help File. It also says - "not in operation" in the description for it. Does that mean you don't have to check this box when you add a wideband? Just setup the Wideband Lamda Input under the Settings and that's it?
03' RSX Type-S
I/H/E/RBC/K-PRO/100shot/555R's
13.2 @ 109mph w/ 2.0 60'
I/H/E/RBC/K-PRO/100shot/555R's
13.2 @ 109mph w/ 2.0 60'
go to options , settings. select use external instead of stock wideband. select the wideband senor you are using. if your using AEM there is no setting for it , so use PLX setting. once car is running and your reading the wideband. fill in the voltage offset box in the same place to make Kmanager read the same EXACTLY as the gauge for the wideband. your done.
the stock wideband can read as low as 10.7. you dont wanna bet me , youl lose your money , lol. i dont care what that link says. and im certain hondata can confirm this for you , simply cause , its fact.
the stock wideband can read as low as 10.7. you dont wanna bet me , youl lose your money , lol. i dont care what that link says. and im certain hondata can confirm this for you , simply cause , its fact.