Page 1 of 2
I need a tuned map for a stock Euro EP3 K20A2. Help please
Posted: Tue Jun 14, 2011 9:50 am
by zeroprobe
Hi,
I've just bought a KPRO and I don't think it comes with a tuned map for a stock Euro EP3 K20A2.
I've searched on here and only see KAL files for EP3's with additional mods.
Would the base calibration ( k20a2-civictyper-tuned.kal ) suit my set up? I notice the VTEC is lowered but the rev limiter is still at 8100.
Can anyone help?
Thanks.
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Fri Nov 11, 2011 12:27 am
by seanyreeves
my tuned k20 makes 215whp on the hub dyno, only a header and induction kit. can upload the kal for that if you would like
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Sun Nov 13, 2011 3:17 pm
by zeroprobe
Hi,
Sure that be good thanks. Whats the VTEC kick in at?
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Nov 16, 2011 4:25 pm
by seanyreeves
lower boundary is 4600 and upper is 6500, it has been tuned by romain levesque at eurospec2000. very reputable tuner.
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Nov 16, 2011 4:26 pm
by seanyreeves
see attachement, running open loop as my o2 sensors arent wired in,
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Thu Nov 17, 2011 5:17 pm
by zeroprobe
Thanks,
One quick question, obviously not going to be 100% but would a race header and intake make this map completely unsuitable for a standard EP3?
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Feb 13, 2013 3:34 am
by windspot
seanyreeves wrote:see attachement, running open loop as my o2 sensors arent wired in,
my car is wired there, i have to make it closed loop?
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Feb 13, 2013 6:23 am
by Nazul
seanyreeves wrote:my tuned k20 makes 215whp on the hub dyno, only a header and induction kit. can upload the kal for that if you would like
215 whp, i think u mean bhp, not even a s2000 makes 215 whp
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Feb 13, 2013 6:30 am
by Nazul
Why is immobilizer disabled, purge system disabled and ELD disabled?
Did u do a swap?
Then this map is not suitable for other users.
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Feb 13, 2013 6:37 am
by Nazul
Since there is an overal fuel trim of 20%, running this map on a normal setup without header, will result in too rich mixture, fucking your engine on long term, so adapt this to 0.
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Feb 13, 2013 8:16 am
by windspot
Nazul wrote:Since there is an overal fuel trim of 20%, running this map on a normal setup without header, will result in too rich mixture, fucking your engine on long term, so adapt this to 0.
can you modify this calibration and upload it so i can load it to the ecu?
im not an expert in this, thats why im asking and i want to thank you for your time and help
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Wed Feb 13, 2013 9:50 am
by Nazul
Yes i can do this tomorrow sorry no k manager installed on windows 8 here at home only at work.
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Thu Feb 14, 2013 1:02 am
by Nazul
Here u go this calibration is adapted for closed loop all sensors on and no fuel trim
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Thu Feb 14, 2013 1:09 am
by windspot
thank you very much!!!
where are you from?
if you come to greece i owe you a drink
Re: I need a tuned map for a stock Euro EP3 K20A2. Help plea
Posted: Thu Feb 14, 2013 1:25 am
by Nazul
Belgium, a little bit too far to just come over ;-)