K-Series Programmable ECU Calibration updates / downloads
Crxmanror
Posts: 29 Joined: Fri Jan 02, 2009 6:00 pm
Location: Colorado Springs,CO
Post
by Crxmanror » Sun Mar 15, 2009 2:24 pm
Let me know what you think.
Attachments
Baseline.kdl
(153.06 KiB) Downloaded 498 times
fonz600
Posts: 239 Joined: Sun Jul 30, 2006 11:57 am
Post
by fonz600 » Sun Mar 15, 2009 3:51 pm
Your running lean dude. Quite lean in fact at some points.
cranny
Posts: 488 Joined: Sat Feb 23, 2008 9:58 pm
Post
by cranny » Sun Mar 15, 2009 4:58 pm
wowsers , haha. holy lean batman. are you running the ITR map? man your car has alot more to offer wih a few datalogs and adjustments.
Crxmanror
Posts: 29 Joined: Fri Jan 02, 2009 6:00 pm
Location: Colorado Springs,CO
Post
by Crxmanror » Sun Mar 15, 2009 6:23 pm
ya i am running the ITR map from Hondata. I made some changes and have yet to do another datalog. One question i do have is...Is it better to datalog in open loop or to let the ECU handle all of that?
cranny
Posts: 488 Joined: Sat Feb 23, 2008 9:58 pm
Post
by cranny » Sun Mar 15, 2009 6:34 pm
if your tuning WOT only , leaving it in closed loop is fine. if your part thottle tuning , must be in open loop.
Crxmanror
Posts: 29 Joined: Fri Jan 02, 2009 6:00 pm
Location: Colorado Springs,CO
Post
by Crxmanror » Mon Mar 16, 2009 8:20 am
thanks for your help cranny... really appreciate it. I think I'm gonna try increasing fuel in 1% increments pretty much across the board and see where that gets me. Do you think thats a good starting point?
fonz600
Posts: 239 Joined: Sun Jul 30, 2006 11:57 am
Post
by fonz600 » Mon Mar 16, 2009 2:00 pm
Not really,
Use the lambda overlay if your not sure what your doing.
cranny
Posts: 488 Joined: Sat Feb 23, 2008 9:58 pm
Post
by cranny » Mon Mar 16, 2009 2:51 pm
just post a datalog and lets have a look see.
Crxmanror
Posts: 29 Joined: Fri Jan 02, 2009 6:00 pm
Location: Colorado Springs,CO
Post
by Crxmanror » Mon Mar 16, 2009 6:16 pm
Also my car runs at WOT in column 7, when i make changes do i need to be making changes to column 7 only or do i need to be changing columns 6 through 9?
Last edited by
Crxmanror on Tue Mar 17, 2009 8:08 pm, edited 1 time in total.
cranny
Posts: 488 Joined: Sat Feb 23, 2008 9:58 pm
Post
by cranny » Mon Mar 16, 2009 9:26 pm
you need to post your fuel map as well buddy.
cranny
Posts: 488 Joined: Sat Feb 23, 2008 9:58 pm
Post
by cranny » Tue Mar 17, 2009 9:14 pm
your not getting wide open throttle for one reason or another. couldnt tell you why. your tps says its getting full but the map dont.
try this one
Attachments
Hondata ITR Map new.kal
(51.02 KiB) Downloaded 344 times
Crxmanror
Posts: 29 Joined: Fri Jan 02, 2009 6:00 pm
Location: Colorado Springs,CO
Post
by Crxmanror » Tue Mar 17, 2009 9:59 pm
Do you think the elevation im at would have anything to do with the map not getting up into the higher columns?
cranny
Posts: 488 Joined: Sat Feb 23, 2008 9:58 pm
Post
by cranny » Thu Mar 19, 2009 9:35 am
that question has been answered for you. didyou upload the calibration i gave you? post up another datalog.
Crxmanror
Posts: 29 Joined: Fri Jan 02, 2009 6:00 pm
Location: Colorado Springs,CO
Post
by Crxmanror » Thu Mar 19, 2009 7:35 pm
cranny wrote: that question has been answered for you. didyou upload the calibration i gave you? post up another datalog.
When was my question answered?