Page 2 of 22

Re: SManager software requests

Posted: Tue May 03, 2011 3:18 pm
by Hondata
What is the sensor input that is being used?

Re: SManager software requests

Posted: Tue May 03, 2011 3:57 pm
by turbo-2nr
any chance of boost by speed,its easy to convert an abs sensor to read ground speed witch would help control tire spin

Re: SManager software requests

Posted: Tue May 03, 2011 4:56 pm
by locash
D12 and B6 are being used commonly, as on one car we have exhaust manifold pressure and fuel pressure, some cars use it as a wideband input when they are also using a stock sensor on D14..

I guess a pulldown selection of common sensors would be better than nothing, but having it in the calibration makes more sense.. :)

Re: SManager software requests

Posted: Tue May 03, 2011 5:01 pm
by locash
Boost by speed isnt as easy to implement as one would think. I suppose if they set it up based on the OEM VSS, then you could find a way to use that VSS input to be triggered by the rear wheel speed sensor..

Re: SManager software requests

Posted: Tue May 03, 2011 5:05 pm
by turbo-2nr
yes it would be based for the stock vss, we would have to figure out howto make it work with an abs sensor as long as there was a voltage offset it wouldn't be that difficult on the user end

Re: SManager software requests

Posted: Wed May 04, 2011 12:35 am
by Luke
http://www.adelante-it.de/datasheets/MB-C04.pdf

here a datasheet for a SPP Bluetooth adapter. with something like that, there shouldn't be a big deal to add bluetooth to S300, KPro etc.

best regards Lukas

Re: SManager software requests

Posted: Wed May 04, 2011 1:16 am
by locash
Bluetooth seems like a big waste of resources. I know of another system that supports bluetooth, and nobody cares or uses it.

Re: SManager software requests

Posted: Wed May 04, 2011 2:40 am
by Luke
locash wrote:Bluetooth seems like a big waste of resources. I know of another system that supports bluetooth, and nobody cares or uses it.
just to tune it's wasting recources.

but in combination with datalogging, with apps for smartphones that could show the display, log the data, messure some data (HP/torque calculation, like those streetdyno apps, but on bases of the increase of the engine speed combined with the GPS signal) etc.
in this case this could be pretty interesting.

EDIT: maybe an option of rotating the 3D map would be nice and some calculation options (datalog of revs for calculating the torque, so some kind of streetdyno based on datalogs)

best regards Lukas

Re: SManager V1.5.1 beta

Posted: Wed May 04, 2011 6:22 am
by Johnny_9
Luke wrote:a selectable target lambda option would be great, one for the primary map, one for the secondary map.

well, and more breakpoints than 3 in the options.

*sorry, wrong thread...*

best regards Lukas
Excellent to see support for this feature request :-D

Re: SManager V1.5.1 beta

Posted: Wed May 04, 2011 6:44 am
by Luke
Johnny_9 wrote:
Luke wrote:a selectable target lambda option would be great, one for the primary map, one for the secondary map.

well, and more breakpoints than 3 in the options.

*sorry, wrong thread...*

best regards Lukas
Excellent to see support for this feature request :-D
in my opinion that is a MUST HAVE for detailed work.

best regards Lukas

Re: SManager software requests

Posted: Wed May 04, 2011 6:28 pm
by SPOOLIN
The ground speed sensor ability is a great request


a sensible one also is date stamping or showing the time and date in the Datalogs list.

Re: SManager V1.5.1 beta

Posted: Thu May 05, 2011 5:58 am
by Johnny_9
Luke wrote:
Johnny_9 wrote:
Luke wrote:a selectable target lambda option would be great, one for the primary map, one for the secondary map.

well, and more breakpoints than 3 in the options.

*sorry, wrong thread...*

best regards Lukas
Excellent to see support for this feature request :-D
in my opinion that is a MUST HAVE for detailed work.

best regards Lukas
My fingers are crossed, since it is already implemented in K-Pro! :-D

Re: SManager software requests

Posted: Thu May 05, 2011 8:18 am
by jiggacivic
how about to make the redo/undo buttons greyed out when they cannot go anymore.

Re: SManager software requests

Posted: Thu May 05, 2011 11:23 pm
by Luke
what about to a setting which says how fast the RPM at the limiters recover? meaning: hitting the rev limiter and you can decide if the recovery is 200rpm below the limiter or 20rpm, in example.
same thing of course for LC and FTS

is that possible?

best regards Lukas

Re: SManager software requests

Posted: Fri May 06, 2011 8:55 am
by Hondata
Bluetooth: It's not as easy as you might think because the s300 does not use a serial protocol.

Rev limits: Very early on we found that setting the recovery very close to the cut point was best.