Page 17 of 21

Re: SManager software requests

Posted: Sun Sep 06, 2015 4:14 pm
by rev hard
Bring back settings for the strain gauge, would be great

Re: SManager software requests

Posted: Sat Sep 12, 2015 1:18 am
by Johnny_9
Change is have a X-Y plot of "rpm" vs "rate of change of rpm"

Re: SManager software requests

Posted: Wed Oct 28, 2015 6:37 pm
by Muckman
Closed loop boost control

Re: SManager software requests

Posted: Wed Nov 04, 2015 12:40 pm
by b16bboss
5) Add-on knock module (knock window, frequency, time intergral etc, individual cyl closed loop knock control)

This would be great

Re: SManager software requests

Posted: Sun Nov 08, 2015 2:12 pm
by coupe-r
DIRECT SERIAL LOGGING (Innovate products)

That is all......
Other products been doing this for YEARS. Takes out the ground offsets, noise etc. Live tuning is MUCH better and faster sample rate.

S300 V3 you say? Well you can't log the Digital air fuel ratio into the fuel tables for lambda % offset and real time tuning using the digital input Correct?

Or can I using Sensor Overlay Digital input?
I can't use closed loop digital input but that's because the input needs to go through D14 which is fine...

This is all SOOO much easier if you guys just use their serial protocol into SManager....

Re: SManager software requests

Posted: Sat Nov 14, 2015 4:19 am
by Luke
Boost Control via external knob:

Since the S300 has that boost control option it would just be great, if you could setup your maximum boost (in percent of boostcut) via an external knob hooked up to the V3.

if anyhow possible with some feedback in the dash cluster. so setting the boost to 40% of maximum boost the VSS goes to 40 for a moment and then back to the VSS signal from the transmission.

just a thought I had.

kind regards Lukas

Data Log Export (CSV) - ECTc AITc

Posted: Wed Dec 16, 2015 1:27 am
by Johnny_9
Can we get the ECTc and IATc variables exported in the CSV?

I am doing and X-Y-Z plot of A/F,ECT vs ECTc to optimise cold starts and warm-up enrichments

Thanks

Re: Data Log Export (CSV) - ECTc AITc

Posted: Wed Dec 16, 2015 10:22 am
by Hondata
Johnny_9 wrote:Can we get the ECTc and IATc variables exported in the CSV?
Done

Re: Data Log Export (CSV) - ECTc AITc

Posted: Tue Jan 05, 2016 2:30 am
by Johnny_9
Hondata wrote:
Johnny_9 wrote:Can we get the ECTc and IATc variables exported in the CSV?
Done
Thanks; can you kindly post the Beta!

Re: SManager software requests

Posted: Tue Jan 05, 2016 6:08 am
by Hondata
The next release is due in the next couple of days.

Re: SManager software requests

Posted: Tue Jan 26, 2016 7:31 am
by b16bboss
Can we have something in protection that can pull timing when it sees voltage or don't from an input like a knock module

Re: SManager software requests

Posted: Fri Feb 19, 2016 4:55 am
by AREA876
Still would love to have more adjust ability over target Lambda table than just three points

Re: SManager software requests

Posted: Fri Feb 19, 2016 5:01 am
by AREA876
Would love to be able to view target Lambda in display and be able to do a graph trace of both target and actual Lambda

Re: SManager software requests

Posted: Thu Apr 21, 2016 11:08 pm
by skullbasher
Would it be possible to add a feature to the quickspool section that allows you to change the fixed amount of duty cycle (99%) when triggered? This would give us a bit more tunability of the powerband/boost curve. Thanks.

Re: SManager software requests

Posted: Thu Apr 21, 2016 11:13 pm
by skullbasher
A secondary quickspool table would also be convenient for the high boost table.