SManager V2.2.7 (beta)

s300 and SManager software questions & answers
Luke
Posts: 249
Joined: Thu Mar 26, 2009 10:24 am
Location: Dorsten/Germany

Re: SManager V2.2.5 (beta)

Post by Luke » Wed Apr 03, 2013 9:39 am

i thought, that there wasn't a timer on the chip.
just a mistake by me.

those kind of requests are in the software request thread.

but this is a thread, where you answer. that's really great.
i think, everybody is looking for such a support.

just as I sad: idea - pros/cons - you know, what we would like to have. we know if it's possible.

EDIT: really sorry, Hondata. although I work with the software for so long, but I've never seen that export option! just knew that video export thingy.
my fault! really sorry for that.

best regards Lukas

Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager V2.2.5 (beta)

Post by Johnny_9 » Thu Apr 04, 2013 5:25 am

Hondata wrote:Lukas, you'll need to clarify your response.

What do you mean about an on-chip timer? What is the purpose of this?

Why can't you export datalogs and use the data that way?

This should be in the software requests thread, so I may move the posts over.

becoz the dataset of the datalog export is (very) limited

whiterabbit
Posts: 4
Joined: Fri Feb 08, 2013 10:48 pm

Re: SManager V2.2.5 (beta)

Post by whiterabbit » Sat Apr 06, 2013 9:52 pm

Is there some reason why we can't add more than 20 rows to the ignition and fuel tables?

Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager V2.2.5 (beta)

Post by Johnny_9 » Tue Apr 09, 2013 7:21 am

whiterabbit wrote:Is there some reason why we can't add more than 20 rows to the ignition and fuel tables?
use boost tables

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: SManager V2.2.5 (beta)

Post by SPOOLIN » Tue Apr 09, 2013 8:49 am

Johnny_9 wrote:
whiterabbit wrote:Is there some reason why we can't add more than 20 rows to the ignition and fuel tables?
use boost tables
he said ROWS not COLUMNS.
www.MSSRACING.com
9.29 | 6.20 | 167

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: SManager V2.2.5 (beta)

Post by SPOOLIN » Tue Apr 09, 2013 8:58 am

a nice checkbox that would be good is to disable burnout rev limiter overriding launch limiter (to make use of antilag, and soft limiter for initializing burnout)
www.MSSRACING.com
9.29 | 6.20 | 167

AREA876
Posts: 400
Joined: Tue Jun 15, 2010 6:14 am
Location: Jamaica

Re: SManager V2.2.6 (beta)

Post by AREA876 » Fri May 03, 2013 7:32 am

Notice a problem with the Flex Fuel and Close Loop operation (V2.2.6 beta).

Flex Fuel Voltage compensation starts and ends with 5 volts.

Close Loop operation does not take affect until you open and close the setting window.

User avatar
Hondata
Site Admin
Posts: 8811
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: SManager V2.2.6 (beta)

Post by Hondata » Fri May 03, 2013 9:01 am

Can you be more specific? Do you mean the ethanol content compensation table? It goes from 0V to 5V here. If not, post the calibration.

Closed loop operation - do you mean that the ECU runs in open loop, or is there some other setting which changes when you open and close the settings window?
Hondata

AREA876
Posts: 400
Joined: Tue Jun 15, 2010 6:14 am
Location: Jamaica

Re: SManager V2.2.6 (beta)

Post by AREA876 » Fri May 03, 2013 10:23 am

Flex Fuel - after saving calibration it reverts back to the first voltage been 5 volts not 0 volts.

Close Loop - If I'm to switch from open loop to close loop wideband input the other parameters (conditional, short term fuel trim, rate of change) are not activated until I open and close setting window.
Attachments
Normal Index.skl
(42.29 KiB) Downloaded 51 times

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: SManager V2.2.6 (beta)

Post by SPOOLIN » Sun May 05, 2013 6:44 pm

getting this error after install AND restarting. getting it when i try to open a calibration by double clicking the file. I can load the file from FILE OPEN just fine. This happens with any calibration as well.

see attached.
Attachments
error.jpg
error message
error.jpg (18.94 KiB) Viewed 3119 times
www.MSSRACING.com
9.29 | 6.20 | 167

rafael_vti
Posts: 27
Joined: Sun Nov 18, 2012 9:12 pm

Re: SManager V2.2.6 (beta)

Post by rafael_vti » Mon May 06, 2013 4:16 am

SPOOLIN wrote:getting this error after install AND restarting. getting it when i try to open a calibration by double clicking the file. I can load the file from FILE OPEN just fine. This happens with any calibration as well.

see attached.
Same thing here!

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: SManager V2.2.6 (beta)

Post by SPOOLIN » Mon May 06, 2013 5:01 am

Win7 64
www.MSSRACING.com
9.29 | 6.20 | 167

User avatar
Hondata
Site Admin
Posts: 8811
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: SManager V2.2.6 (beta)

Post by Hondata » Mon May 06, 2013 9:08 am

Thanks for the report. We've fixed this and will make another release today.
Hondata

SPOOLIN
Posts: 143
Joined: Sun Mar 20, 2005 10:47 pm
Location: North Georgia
Contact:

Re: SManager V2.2.6 (beta)

Post by SPOOLIN » Mon May 06, 2013 9:31 am

Ok let us know.
www.MSSRACING.com
9.29 | 6.20 | 167

ketchu13
Posts: 10
Joined: Mon Jun 04, 2007 11:05 am

Re: SManager V2.2.7 (beta)

Post by ketchu13 » Tue May 07, 2013 4:46 am

Thanks for this new release !
Act a fool !

Locked