all motor b16a calibration in need!!

Calibrations for S-Manager - Use all calibrations at your own risk (dyno tuning recommended)
Post Reply
mitchb16a
Posts: 2
Joined: Wed Feb 11, 2015 9:16 am

all motor b16a calibration in need!!

Post by mitchb16a » Wed Feb 11, 2015 9:31 am

Iv got a freshley rebuilt b16a with 17, 000km on it. Has a header back 2.5inch magnaflow exhaust, password jdm intake, a set of 2001 USDM ITR cams and springs. Stock Iinjectors. Using a jdm b16 basemap right now but I feel like a little more could be pushed out of it. Runs a bit rich I fined but thats the least of my worries.New to thd Hondata system and dont want to screw something up on my build. All help Iis appriciated!!

cam6222
Posts: 18
Joined: Sat Feb 21, 2015 10:42 pm
Location: malaysia
Contact:

Re: all motor b16a calibration in need!!

Post by cam6222 » Fri Apr 17, 2015 7:13 pm

I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
The attachment Wfb8922 16a.skl is no longer available
Attachments
Wfb8922 16a.skl
(40.05 KiB) Downloaded 316 times
Mrs Autoparts @ Honda Parts Malaysia

Monnoracing
Posts: 110
Joined: Sun Aug 28, 2011 11:41 pm

Re: all motor b16a calibration in need!!

Post by Monnoracing » Thu Apr 23, 2015 12:36 am

only tune I have that has your setup. This car ran good with this tune
Attachments
Enrique Garcia B16a2 WB.skl
(40.04 KiB) Downloaded 336 times

Kevinbrahh
Posts: 2
Joined: Wed May 06, 2015 8:13 pm

Re: all motor b16a calibration in need!!

Post by Kevinbrahh » Wed May 06, 2015 8:18 pm

cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Wfb8922 16a.skl
Hi do you have basemap for Injen CAI with 421 headers and 2.5 exhaust? I am doing an engine build soon so I don't want to tune my car yet. Thank you!!!

cam6222
Posts: 18
Joined: Sat Feb 21, 2015 10:42 pm
Location: malaysia
Contact:

Re: all motor b16a calibration in need!!

Post by cam6222 » Thu Jun 11, 2015 2:49 am

Kevinbrahh wrote:
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
The attachment Wfb8922 16a.skl is no longer available
Hi do you have basemap for Injen CAI with 421 headers and 2.5 exhaust? I am doing an engine build soon so I don't want to tune my car yet. Thank you.

Look for this attachment
PDG45.skl
(40.05 KiB) Downloaded 163 times
Mrs Autoparts @ Honda Parts Malaysia

ecronic
Posts: 20
Joined: Tue Jun 14, 2011 2:37 pm

Re: all motor b16a calibration in need!!

Post by ecronic » Fri Nov 25, 2016 12:02 am

cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.

Wfb8922 16a.skl
I know this is a very old thread but could really use your help.

I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.

Please suggest the best possible basemap you have that matches to the mods below:

B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.

Hope to hear from you soon.

Thanks & regards
Dev
Thanks & Regards
------------------------------
Ecronic

Zperformance
Posts: 100
Joined: Thu Jul 14, 2016 12:32 pm
Location: Fresno,Ca

Re: all motor b16a calibration in need!!

Post by Zperformance » Thu Dec 08, 2016 9:03 am

ecronic wrote:
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.

Wfb8922 16a.skl
I know this is a very old thread but could really use your help.

I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.

Please suggest the best possible basemap you have that matches to the mods below:

B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.

Hope to hear from you soon.

Thanks & regards
Dev
Hey Dev, you should be able to run your car with a hondata s300 basemap (b16/p30 map). Since you only have minor mods it should be capable to run your car.

ecronic
Posts: 20
Joined: Tue Jun 14, 2011 2:37 pm

Re: all motor b16a calibration in need!!

Post by ecronic » Thu Dec 08, 2016 9:22 am

Zperformance wrote:
ecronic wrote:
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.

Wfb8922 16a.skl
I know this is a very old thread but could really use your help.

I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.

Please suggest the best possible basemap you have that matches to the mods below:

B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.

Hope to hear from you soon.

Thanks & regards
Dev
Hey Dev, you should be able to run your car with a hondata s300 basemap (b16/p30 map). Since you only have minor mods it should be capable to run your car.
Hi Zperformance

Thanks for replying. I'm just worried about running lean or rich. I've got afr gauge installed so guess I'm going to go ahead with that map and post the result. Let's hope someone can help out then setting up the fuel tables.

Cheers
Dev

Zperformance
Posts: 100
Joined: Thu Jul 14, 2016 12:32 pm
Location: Fresno,Ca

Re: all motor b16a calibration in need!!

Post by Zperformance » Sat Dec 10, 2016 2:53 pm

Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.

ecronic
Posts: 20
Joined: Tue Jun 14, 2011 2:37 pm

Re: all motor b16a calibration in need!!

Post by ecronic » Sat Dec 10, 2016 7:53 pm

Zperformance wrote:Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Okay so I tried the s300 cal for b16a/ p30 & the check engine light came on. Errors that shoot up are oxygen sensor heater & knock sensor. My stock ecu doesn't have any errors.

Fyi
Stock ecu: P30 & s300 ecu: p28

Appreciate you replying my posts Zperformance and thanks to anyone who can some light on this.

Cheers
Dev

Zperformance
Posts: 100
Joined: Thu Jul 14, 2016 12:32 pm
Location: Fresno,Ca

Re: all motor b16a calibration in need!!

Post by Zperformance » Wed Dec 14, 2016 10:11 am

ecronic wrote:
Zperformance wrote:Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Okay so I tried the s300 cal for b16a/ p30 & the check engine light came on. Errors that shoot up are oxygen sensor heater & knock sensor. My stock ecu doesn't have any errors.

Fyi
Stock ecu: P30 & s300 ecu: p28

Appreciate you replying my posts Zperformance and thanks to anyone who can some light on this.

Cheers
Dev
Go through the paramateres and you can disable it. If you are not sure, let me know i will disable them and upload it here for you.

Zperformance
Posts: 100
Joined: Thu Jul 14, 2016 12:32 pm
Location: Fresno,Ca

Re: all motor b16a calibration in need!!

Post by Zperformance » Wed Dec 14, 2016 10:24 am

basically P30 basemap i just disable the sensors
Attachments
P30.skl
*use at your own risk
(45.57 KiB) Downloaded 89 times

Post Reply